Geometry

Geometry panel.

Offset

Moves the extrusion parallel to the curve normals.

Bézier Circle -1 offset, 0.5 extrusion, 0.25 Bevel Depth, 10 Bevel resolution.

Extrude

Will extrude the curve along both the positive and negative local Z axes. Turns a one-dimensional curve into a two-dimensional curve by giving it height. With a scale is the sum of both directions, perpendicular to the curve’s normals.

Bézier Circle 0.0 extrude (Edit Mode).

Extruded by 0.5 (Object Mode).

Taper Object

The taper curve is evaluated along the local X axis, using the local Y axis for width control. Note also that: Tapering a curve causes it to get thinner towards one end. You can also alter the proportions of the Taper throughout the tapered object by moving/scaling/rotating the control points of the Taper Object. The Taper Object can only be another curve. Editing the handles and control points of the Taper Object will cause the original Object to change shape.

In order for this to work:

• It must be an open curve.

• The taper is applied independently to all curves of the extruded object.

• Only the first curve in a Taper Object is evaluated, even if you have several separated segments.

• The scaling starts at the first control point on the left and moves along the curve to the last control point on the right.

• Negative scaling, (e.g. negative local Y on the taper curve) is possible as well. However, rendering artifacts may appear.

• Might need to increase the curve resolution to see more detail of the taper.

• With closed curves, the taper curve in Taper Object acts along the whole curve (perimeter of the object), not just the length of the object, and varies the extrusion depth. In these cases, you want the relative height of the Taper Object Taper curve at both ends to be the same, so that the cyclic point (the place where the endpoint of the curve connects to the beginning) is a smooth transition.

Map Taper

For curves using a Taper Object and with modifications to the Start/End Bevel Factor the Map Taper option will apply the taper to the beveled part of the curve (not the whole curve).

Bevel

Depth

Changes the size of the bevel.

A curve with different Bevel depths applied (Depth of 0.05).

A curve with different Bevel depths applied (Depth of 0.25).

Resolution

Alters the smoothness of the bevel.

A curve with different resolutions applied (Resolution of 1).

A curve with different resolutions applied (Resolution of 12).

Object

Here you can specify a curve object (opened or closed) which will be extruded along the curve. If your object’s shape is 3D, it will be projected to its local XY plane before the extrusion. You can check how the projected Object looks like by switching its shape to 2D.

Wichtig

Make sure the shape you want to extrude is in the Object’s local XY plane. If it is in the local XZ or YZ plane, it will be reduced to a line when it is projected to the local XY plane. Because of this, the extruded shape will be a flat plane.

A curve with a Bézier curve as the Bevel Object.

A curve with a Bézier circle as the Bevel Object.

Fill Caps

Seals the ends of a beveled curve.

Bevel Start/End

These options determine where to start/end the Bevel operation on the curve. This allows to make a bevelled curve which is not fully covered with a bevel.

Increasing the Start Bevel Factor to 0.5 will start beveling the curve 50% of the distance from the start of the curve (in effect shortening the curve). Decreasing the End Bevel Factor by 0.25 will start beveling the curve 25% of the distance from the end of the curve (again, shortening the curve).

A curve with no Bevel factor applied.

A curve with a 0.6 End Bevel Factor.

Bevel Mapping Start/End

Allows to control the relation between bevel factors (number between 0 and 1) and the rendered start and end point of a beveled spline. Map the bevel factor:

Resolution

To the number of subdivisions of a spline (U resolution).

Segments

To the length of its segments. Mapping to segments treats the subdivisions in each segment of a curve as if they would have all the same length.

Spline

The length of a spline.

Examples

Open 2D Curve

The extrusion will create a „wall“ or „ribbon“ following the curve shape. If using a Bevel Depth, the wall becomes a sort of slide or gutter. If your normals are facing the wrong way you can switch their direction as shown here.

Open 2D Curve with Alt-C, fill set to none, zero offset, 0.5 extrusion, 0.25 Bevel Depth, 10 Bevel resolution.

Closed 2D Curve

This is probably the most useful situation, as it will quickly create a volume, with (by default) two flat and parallel surfaces filling the two sides of the extruded „wall“. You can remove one or both of these faces by choosing the fill mode: both, front, back, or none.

The optional bevel depth will always create a 90 degree bevels here.

Closed 2D Curve, 0.5 extrude, 0.25 Bevel Depth, 10 Bevel resolution, Fill: Both.

3D Curve

Here the fact that the curve is closed or not has no importance – you will never get a volume with an extruded 3D curve, only a wall or ribbon, like with open 2D curves.

However, there is one more feature with 3D curves: the Tilt of the control points (see above). It will make the ribbon twist around the curve to create a Möbius strip, for example.

Taper

Let us taper a simple curve circle extruded object using a taper curve. Add a curve, then exit Edit Mode. Add another one (a closed one, like a circle); call it „BevelCurve“, and enter its name in the Bevel Object field of the first curve (Curve tab). We now have a pipe. Add a third curve while in Object Mode and call it „TaperCurve“. Adjust the left control point by raising it up about 5 units.

Now return to the Object tab, and edit the first curve’s Taper Object field in the Geometry panel to reference the new taper curve which we called „TaperCurve“. When you hit enter the taper curve is applied immediately, with the results shown in Fig. Circle curve set as Bevel Object..

Circle curve set as Bevel Object.

Taper extruded curve.

You can see the taper curve being applied to the extruded object. Notice how the pipe’s volume shrinks to nothing as the taper curve goes from left to right. If the taper curve went below the local Y axis the pipe’s inside would become the outside, which would lead to rendering artifacts. Of course as an artist that may be what you are looking for!

Taper example 1.

In Fig. Taper example 1. you can clearly see the effect the left taper curve has on the right curve object. Here the left taper curve is closer to the object origin and that results in a smaller curve object to the right.

Taper example 2.

In Fig. Taper example 2. a control point in the taper curve to the left is moved away from the origin and that gives a wider result to the curve object on the right.

Taper example 3.

In Fig. Taper example 3. we see the use of a more irregular taper curve applied to a curve circle.

Bevel extrusion with Tilt example.