Draw Brush

Draw brushes are the special type of brushes that uses Grease Pencil for drawing tools. The brush can be changed in the Tool Settings.

The different draw brushes (pencil, Ink, marker, etc.) are settings variations of the same Draw Brush. You can create many brushes, each with unique settings to get different artistic result while drawing.

Tool Settings

Brushes

Brush data-block panel.

Brush

The Data-Block Menu to select a preset brush type or a custom brush.

Add Brush

When you add a brush, the new brush is a clone of the current one.

Brush Specials

Reset Brush

Reset the current brush to its default settings.

Reset All Brushes

Reset all brushes to their default settings.

Custom Icon

Allows definition of a custom brush icon.

Image Path

Defines the path to the image to use as custom icon.

Note

In order to save a custom brush in a blend-user, enable Fake User.

Brush Settings

Material

Data-block selector for the material.

Radius

The radius of the brush in pixels.

F allows you to change the brush size interactively by dragging the mouse/pen or by typing a number then confirm.

Use Pressure (pressure sensitivity icon)

Uses stylus pressure to control how strong the effect is.

Strength

Control the stroke transparency (alpha). From totally transparent (0.0) to fully opaque (1.0).

You can change the brush strength interactively by pressing Shift-F in the 3D Viewport and then moving the mouse/pen and then LMB. You can also enter the size numerically.

Use Pressure (pressure sensitivity icon)

Uses stylus pressure to control how strong the effect is.

Advanced

Input Samples

Controls how often the input device is read to generate points on the stroke. Higher values give a higher precision (more points) but produce an irregular stroke, while lower values give a lower precision (fewer points) but produce a soften stroke. (0 disabled extra input device samples.)

You have to set up this value according to your input device to obtain the right balance between accuracy and softness for your strokes. See Input Device for more information.

Active Smooth

The number of smoothing iterations to apply to the stroke while drawing.

Angle

Direction of the input device that gives the maximum thickness to the stroke (0° for horizontal).

Factor

Amount of thickness reduction when the stroke is perpendicular to the Angle value.

Hardness

Amount of transparency (alpha) to apply from the border of the point to the center. Works only when the brush is using stroke materials of Dot or Box style.

Aspect Ratio

Controls the width and height of the alpha gradient.

X, Y

Stroke

Post-Processing

Post-processing methods that are executed on the strokes when you finished drawing, right after releasing the LMB or Pen tip. You can toggle the use of post-processing using the checkbox in the section panel header.

Smooth

Strength of smoothing process on the points location along the stroke.

Iterations

The number of smoothing iterations to apply to the stroke.

Subdivision Steps

Number of subdivisions to apply to newly created strokes.

Simplify

Reduces final points numbers in the stroke with an adaptive algorithm.

Trim Strokes End

Automatically trim intersection strokes ends.

Randomize

Adds randomness to the position of the points along the stroke. You can toggle the use of Randomize using the checkbox in the section panel header.

Pressure

The amount of randomness to apply using the pressure of the input device.

Strength

The amount of randomness to apply to the stroke strength value (alpha).

UV

The amount of randomness to apply to the UV rotation.

Jitter

The amount of jittering to add to the stroke.

Use Pressure (pressure sensitivity icon)

Uses the stylus pressure to control how strong the effect is.

Stabilize Stroke

Stabilize Stroke helps to reduce jitter of the strokes while drawing by delaying and correcting the location of points. You can toggle the use of Stabilize Stroke using the checkbox in the section panel header.

Radius

Minimum distance from the last point before the stroke continues.

Factor

A smooth factor, where higher values result in smoother strokes but the drawing sensation feels like as if you were pulling the stroke.

Curves

For more precise control on some strokes properties you can use a curve widget.

Sensitivity

Controls the sensitivity of the input device.

Strength

Controls the stroke strength (alpha).

Jitter

Controls the jitter amount on the stroke.

Cursor

The cursor can be disabled by toggling the checkbox in the Cursor header.

Show Fill Color While Drawing

Shows the brush linked material color in the viewport.