Brush Settings(ブラシ設定)
- Radius(半径)
This option controls the radius of the brush, measured in pixels. F allows you to change the brush size interactively by dragging the mouse and then LMB (the texture of the brush should be visible inside the circle). Typing a number then enter while using F allows you to enter the size numerically.
- Size Pressure(サイズの筆圧)
グラフィックタブレット を使用している場合は、筆圧感知アイコンを有効にすることでブラシサイズに影響を与えることができます。
- Use Unified Radius(共通の半径を使用)
すべてのブラシで同じブラシ 半径 を使用します。
- Radius Unit
Controls how the brush Radius is measured.
- View(ビュー)
The Radius is measured based on how the cursor appears on the monitor i.e. "screen space".
- Scene(シーン)
The Radius is measured based on real world units. The unit type and scaling can be configured in the Scene Units.
- Strength(強さ)
Controls how much each application of the brush affects the model. For example, higher values cause the Draw brush to add depth to the model more quickly, and cause the Smooth brush to smooth the model more quickly. This setting is not available for Grab, Snake Hook, or Rotate.
You can change the brush strength interactively by pressing Shift-F in the 3D Viewport and then moving the brush and then LMB. You can enter the size numerically also while in Shift-F sizing.
- Strength Pressure
Brush strength can be affected by enabling the pressure sensitivity icon, if a supported tablet is being used.
- Use Unified Strength(共通の強度を使用)
すべてのブラシで同じブラシの Strength(強さ) を使用します。
ちなみに
If the range of strengths does not seem to fit the model (for example, if even the lowest strength setting still makes too large of a change on the model) then you can scale the model (in Edit Mode, not Object Mode). Larger sizes will make the brush's effect smaller, and vice versa.
- Direction Ctrl
Brush direction toggle, Add raises geometry towards the brush, Subtract lowers geometry away from the brush. This setting can be toggled with Ctrl while sculpting.
- Normal Radius
The ratio between the brush radius and the radius that is going to be used to sample the normal i.e. take the average of multiple normals. This influences the brush orientation; increasing this value causes the brush to follow a smooth version of the mesh, while a small value causes the brush to closely follow the contours of the mesh.
- Hardness (硬さ)
How close the brush falloff starts from the edge of the brush.
- Autosmooth
Sets the amount of smoothing to be applied to each stroke.
- Topology(トポロジー)
See Dyntopo.
- Normal Weight Ctrl
Constrains brush movement along the surface normal. Especially useful with the Grab brush, can be temporarily enabled by holding Ctrl. E.g. Grab brush can be used to push a depression (hole) into the mesh when Normal Weight is set.
Applies to Grab and Snake Hook brushes.
- Plane Offset
Offset for planar brushes (Clay, Fill, Flatten, Scrape), shifts the plane that is found by averaging the faces above or below.
- Plane Trim
Ability to limit the distance that planar brushes act. If trim is enabled vertices that are further away from the offset plane than the trim distance are ignored during sculpting.
高度な設定
- Auto-Masking
The auto-masking toggles in the brush settings are the same as the sculpt mode auto-masking settings. The difference is that these toggles can be customized per brush to create specific brush behaviors.
参考
Auto-Masking For more information on the Auto-Masking toggles, see Auto-Masking.
- Sculpt Plane
Use this menu to set the plane in which the sculpting takes place. In other words, the primary direction that the vertices will move.
- Area Plane
The movement takes place in the direction of average normal for all active vertices within the brush area. Essentially, this means that the direction is dependent on the surface beneath the brush.
- View Plane
Sculpting in the plane of the current 3D Viewport.
- X, Y, Z Plane
The movement takes place in the positive direction of one of the global axes.
- Original(オリジナル)
- Normal(ノーマル)
When locked it keeps using the normal of the surface where stroke was initiated, instead of the surface normal currently under the cursor.
- Plane(平面)
When locked keep using the plane origin of surface where stroke was initiated, instead of the surface plane currently under the cursor.
- Accumulate(蓄積)
Causes stroke dabs to accumulate on top of each other.
- Front Faces Only
When enabled, the brush only affects vertices that are facing the viewer.
Texture(テクスチャ)
See the global brush settings for Texture settings.
Stroke
See the global brush settings for Stroke settings.
Falloff(減衰)
See the global brush settings for Falloff settings.
Cursor(カーソル)
See the global brush settings for Cursor settings.