Chọn Cái Đã Kết Nối (Select Linked)

Kết Nối (Linked)

Tham Chiếu (Reference)

Chế Độ (Mode)

Chế Độ Biên Soạn (Edit Mode)

Trình Đơn (Menu)

Select ‣ Select Linked ‣ Linked

Tổ Hợp Phím Tắt (Shortcut)

Ctrl-L

Select geometry connected to already selected elements. This is often useful when a mesh has disconnected, overlapping parts, where isolating it any other way would be tedious. To give more control, you can also enable delimiters in the Điều Chỉnh Thao Tác Trước Đây (Adjust Last Operation) panel, so the selection is constrained by seams, sharp edges, materials or UV islands.

With Pick Linked you can also select connected geometry directly under the cursor, using the L shortcut to select or Shift-L to deselect linked. This works differently in that it uses the geometry under the cursor instead of the existing selection.

Đường Ngắn Nhất (Shortest Path)

Tham Chiếu (Reference)

Chế Độ (Mode)

Chế Độ Biên Soạn (Edit Mode)

Trình Đơn (Menu)

Select ‣ Select Linked ‣ Shortest Path

Tổ Hợp Phím Tắt (Shortcut)

Ctrl-LMB

Select a face or vertex path with Ctrl-LMB.

Selects all geometry along the shortest path from the active vertex, edge, or face to the one which was selected.

Dấu Cạnh [duy trong chế độ chọn Cạnh] (Edge Tag [in Edge select mode only])

This select button indicates what should be done when selecting a vertex path with Ctrl-LMB:

Chọn (Select)

Just selects all the edges in the path.

Nhãn Đường Khâu (Tag Seam)

Marks all edges in the path as seams for UV unwrapping.

Nhãn Sắc Nhọn (Tag Sharp)

Marks all edges in the path as sharp for the Edge Split Modifier.

Nhãn Nếp Gấp (Tag Crease)

Marks all edges in the path as creases for the Subdivision Surface Modifier, with weight 1.0.

Nhãn Bo Tròn (Tag Bevel)

Gives bevel weight 1.0 (for the Bevel Modifier) to all edges in the path.

Nhãn Dấu Cạnh PCTD (Tag Freestyle Edge Mark)

Marks all edges in the path as Freestyle edges.

Bước Bậc Thang theo Bề Mặt (Face Stepping)

Supports diagonal paths for vertices and faces, and selects edge rings with edges.

Khoảng cách Cấu Trúc Liên Kết (Topological Distance)

Only takes into account the number of edges of the path and not the length of the edges to calculate the distances.

Phủ Kín Vùng Shift-Ctrl-NCT (LMB)

Selects all elements in the shortest paths from the active selection to the clicked area.

Các Tùy Chọn về Bỏ Chọn So Le (Checker Deselect Options)

Allows to quickly select alternate elements in a path.

Số Phần Tử Không Chọn (Deselected)

The number of deselected elements in the repetitive sequence.

Cái được Chọn (Selected)

The number of selected elements in the repetitive sequence.

Dịch Chuyển (Offset)

Dịch chuyển từ điểm khởi đầu.

Các Mặt Phẳng Kết Nối (Linked Flat Faces)

Tham Chiếu (Reference)

Chế Độ (Mode)

Chế Độ Biên Soạn (Edit Mode)

Trình Đơn (Menu)

Select ‣ Select Linked ‣ Linked Flat Faces

Selects all connected faces with a similar angle.

Độ Sắc Nhọn (Sharpness)

Select connected faces with a reference angle less than the value specified.

Looking at the image above, when at least one face is selected (as seen on the left), Linked Flat Faces will select all connecting faces that lie on the same or similar plane (as shown in the middle image). If the corners are smoothed, those faces are no longer lined up with the selected faces. At this point, increasing the Sharpness value in the tool options could include the smoothed faces.