F-Curve Modifiers

Reference

Panel:Properties region ‣ Modifiers ‣ Modifiers

F-Curve modifiers are similar to object modifiers, in that they add non-destructive effects, that can be adjusted at any time, and layered to create more complex effects.

Adding a Modifier

../../../_images/editors_graph-editor_fcurves_modifiers_panel.png

Modifiers panel.

The F-Curve modifier panel is located in the Properties region. Select a curve by selecting one of its curve points, or by selecting the channel list. Click on the Add Modifier menu to select a modifier.

Types of Modifiers

Generator

Generator creates a Factorized or Expanded Polynomial function. These are basic mathematical formulas that represent lines, parabolas, and other more complex curves, depending on the values used.

Additive
This option causes the modifier to be added to the curve, instead of replacing it by default.
Polynomial Order

Specify the order of the polynomial, or the highest power of X for this polynomial. (number of coefficients: 1).

Change the Coefficient values to change the shape of the curve.

See also

The Wikipedia Page for more information on polynomials.

Built-in Function

These are additional formulas, each with the same options to control their shape. Consult mathematics reference for more detailed information on each function:

  • Sine
  • Cosine
  • Tangent
  • Square Root
  • Natural Logarithm
  • Normalized Sine (sin(x)/x)
Amplitude
Adjusts the Y scaling.
Phase Multiplier
Adjusts the X scaling.
Phase Offset
Adjusts the X offset.
Value Offset
Adjusts the Y offset.

Envelope

Allows you to adjust the overall shape of a curve with control points.

Reference Value
Set the Y value the envelope is centered around.
Min
Lower distance from Reference Value for 1:1 default influence.
Max
Upper distance from Reference Value for 1:1 default influence.
Add Point
Add a set of control points. They will be created at the current frame.
Point
Frame
Set the frame number for the control point.
Min
Specifies the lower control point’s position.
Max
Specifies the upper control point’s position.

Cycles

Cycles allows you add cyclic motion to a curve that has two or more control points. The options can be set for before and after the curve.

Cycle Mode
Repeat Motion
Repeats the curve data, while maintaining their values each cycle.
Repeat with Offset
Repeats the curve data, but offsets the value of the first point to the value of the last point each cycle.
Repeat Mirrored
Each cycle the curve data is flipped across the X axis.
Before, After Cycles
Set the number of times to cycle the data. A value of 0 cycles the data infinitely.

Noise

Modifies the curve with a noise formula. This is useful for creating subtle or extreme randomness to animated movements, like camera shake.

Blend Type
Replace
Adds a -0.5 to 0.5 range noise function to the curve.
Add
Adds a 0 to 1 range noise function to the curve.
Subtract
Subtracts a 0 to 1 range noise function to the curve.
Multiply
Multiplies a 0 to 1 range noise function to the curve.
Scale
Adjust the overall size of the noise. Values further from 0 give less frequent noise.
Strength
Adjusts the Y scaling of the noise function.
Offset
Offsets the noise in time.
Phase
Adjusts the random seed of the noise.
Depth
Adjusts how detailed the noise function is.

Limits

Limit curve values to specified X and Y ranges.

Minimum, Maximum X
Cuts a curve off at these frames ranges, and sets their minimum value at those points.
Minimum, Maximum Y
Truncates the curve values to a range.

Stepped Interpolation

Gives the curve a stepped appearance by rounding values down within a certain range of frames.

Step Size
Specify the number of frames to hold each frame.
Offset
Reference number of frames before frames get held. Use to get hold for (1-3) vs (5-7) holding patterns.
Use Start Frame
Restrict modifier to only act before its “end” frame.
Use End Frame
Restrict modifier to only act after its “start” frame.