Edges & Faces¶

Edges¶

Buttons for the selection modes.

Edges can be selected in much the same way as vertices and faces by RMB-clicking them while Edge Select Mode is activated. Pressing Shift while clicking will add/subtract to the existing selection.

Edge Loops¶

Reference

Mode:	Edit Mode (Mesh)
Menu:	Select ‣ Edge Loop
Hotkey:	`Alt-RMB`, or `Shift-Alt-RMB` for modifying existing selection

Edge loops can be selected by first selecting an edge (vertex or edge selection mode), and then going to Select ‣ Edge Loop. The shortcut Alt-RMB on an edge (either vertex or edge select mode) is a quicker and more powerful way of doing so. More powerful, because you can add/remove loops from an existing selection if you press Shift too.

Note, that if you want to select a loop while being in vertex select mode, you still have to perform the shortcut on an edge – while you, for just selecting vertices, would RMB on a vertex.

../../../_images/modeling_meshes_selecting_edges-faces_edge-loop-example.png

An edge loop.

Edge Rings¶

Reference

Mode:	Edit Mode (Mesh)
Menu:	Select ‣ Edge Ring
Hotkey:	`Ctrl-Alt-RMB`, or `Shift-Ctrl-Alt-RMB` for modifying existing selection

Edge Rings are selected similarly. Based on the selection of an edge go to Select ‣ Edge Ring. Or use Ctrl-Alt-RMB on an edge.

../../../_images/modeling_meshes_selecting_edges-faces_edge-ring-example.png

An edge ring.

Note

Convert Selection to Whole Faces

If the edge ring selection happened in Edge Select Mode, switching to Face Select Mode will erase the selection.

This is because none of those faces had all its (four) edges selected, just two of them.

Instead of selecting the missing edges manually or by using Shift-Alt-RMB twice, it is easier to first switch to Vertex Select Mode, which will kind of “flood” the selection. A subsequent switch to Face Select Mode will then properly select the faces.

Faces¶

The Face Select Mode activated.

To select parts of a mesh face-wise, you have to switch to Face Select Mode. Do this by clicking the button shown above, or press Ctrl-Tab to spawn a menu. The selection works as usual with RMB; to add/remove to an existing selection, additionally press Shift. The Border, Circle and Lasso Selection Tools must intersect the face indicators usually represented by small pixel squares; one at the center of each face.

Face Loops¶

Reference

Mode:	Edit Mode (Mesh)
Hotkey:	`Alt-RMB` or `Shift-Alt-RMB` for modifying existing selection

Face Loops are pretty much the same as Edge Rings. If you want to select a Face Loop, there is no menu entry that works based on a selected face. Using Select ‣ Edge Ring would select a “cross” with the prior selected face as the middle. If you want to avoid switching to Edge Select Mode to select a Face Loop, use the Alt-RMB shortcut.

../../../_images/modeling_meshes_selecting_edges-faces_face-mode-different-loop-selections.png

Different loop selection operations on a grid in Face Select Mode.

Just the selected face.
Select the face, then Select ‣ Edge Ring. See, how Blender selects edges, even if being in Face Select Mode. If these edges are desired and you want to work on them, switch in Edge Select Mode. Switching to Vertex Select Mode would flood the selection and leave you with the 4th image as result, after going back to Face Select Mode.
Select the face, the Select ‣ Edge Loop. As in the example above, Blender pretends to be in Edge Select Mode and takes the four edges of the selected face as base for the selection operation.
This selection was created by Alt-RMB on the left edge of the center face, followed by twice Shift-Alt-RMB on the top edge of the center face. Two times, because the first click will remove the selected face loop (in this case, just the original selected face), while the second click will add the whole vertical running loop to the selection, creating the cross.

N-gons in Face Select Mode¶

../../../_images/modeling_meshes_selecting_edges-faces_face-mode-ngon-visual-problem.png

N-gon face having its center dot inside another face.

As already known, faces are marked with a little square dot in the middle of the face. With n-gons that can lead in certain cases to a confusing display. The example shows the center dot of the U-shaped n-gon being inside of the oblong face inside the “U”. It is not easy to say which dot belongs to which face (the orange dot in the image is the object origin). Luckily, you do not need to care much, because to select a face, you do not have to click the center dot, but the face itself.

Tip

Face selection

To select a face: Click the face, not the dot!