Pincel

Referência

Panel:Physics ‣ Dynamic Paint
Type:Pincel

The Brush type makes object apply paint on the canvas.

../../_images/physics_dynamic-paint_brush_main-panel.png

Brush main panel.

From the first brush panel you can define how brush affects canvas color surfaces.

Paint Color
Color of the paint.
Alfa
Defines brush alpha or visibility. Final wetness is also affected by alpha.
Umidade
Defines how «wet» new paint is. Wetness is visible on «Paint» surface «wetmap». Speed of «Drip» and «Spread» effects also depends on how wet the paint is.
Alfa absoluto
This setting limits brush alpha influence. Without it, brush is «added» on surface over and over again each frame, increasing alpha and therefore influence of brush on canvas. In many cases however, it is preferred to not increase brush alpha if it already is on brushes level.
Apagar pintura
Makes brush dissolve existing paint instead of adding it.

Fonte

Referência

Type:Pincel
Panel:Physics ‣ Dynamic Paint ‣ Source

Fonte de pintura

Paint Source setting lets you define how brush influence/intersection is defined.

Volume da malha

The Brush affects all surface point inside the mesh volume.

../../_images/physics_dynamic-paint_brush_source-mesh-volume.png

Fonte: Volume de malha.

Proximidade

Only uses defined distance to the closest point on brush mesh surface. Note that inside of the volume is not necessarily affected because it is not close to the surface.

../../_images/physics_dynamic-paint_brush_source-proximity.png

Source: Proximity. Brush affects all canvas pixels around it.

Volume de malha e proximidade

Same as volume type, but also has influence over defined distance.

Proximidade interna
Applies proximity inside the mesh volume.
Negar volume
Negates brush alpha within mesh volume.
../../_images/physics_dynamic-paint_brush_source-mesh-volume-proximity-1.png

The Volume + Proximity brush with no additional settings.

../../_images/physics_dynamic-paint_brush_source-mesh-volume-proximity-2.png

Inner Proximity. Proximity falloff is now visible inside the volume.

../../_images/physics_dynamic-paint_brush_source-mesh-volume-proximity-3.png

Negate Volume. Inner side of the volume has become completely transparent.

../../_images/physics_dynamic-paint_brush_source-mesh-volume-proximity-4.png

Inner Proximity and Negate Volume enabled together.

Centro do objeto

Instead of calculating proximity to the brush object mesh, which can be quite slow in some cases, only distance to only center is calculated. This is much faster and often good enough.

../../_images/physics_dynamic-paint_brush_source-object-center.png

Source: Object Center.

Sistema de partículas

Brush influence is defined by particles from a selected particle system.

Particle Effect: Solid Radius
ToDo 2.62.
Usar raio das partículas
Raio de suavização
ToDo 2.62.
../../_images/physics_dynamic-paint_brush_source-particle-system.png

Fonte: Sistema de partículas

Opções comuns

Distância de pintura
ToDo 2.62.
Projetar

Projects brush to the canvas from a defined direction. Basically this can be considered as «direction aligned» proximity.

../../_images/physics_dynamic-paint_brush_source-project.png

The Project option enabled. See how brush only affects canvas in normal direction.

Decaimento
Falloff type can be «Smooth», «Sharp» or tweaked with a color ramp.

Velocidade

Referência

Type:Pincel
Panel:Physics ‣ Dynamic Paint ‣ Velocity

This panel shows brush options that are based on object velocity.

On top you have a color ramp and several related settings. Basically the color ramp represents brush velocity values: left side being zero velocity and right side being the «Max velocity». Speed is measured in «units per frame».

Checkboxes above can be used to define color ramp influence.

Multiplicar alfa
Uses color ramp’s alpha value depending on current velocity and multiplies brush alpha with it.
Substituição de cor
Replaces the brush color with the values from the Gradiente de cores.
Multiplicar profundidade
Multiplies brushes «depth intersection» effect. Basically you can adjust displace and wave strength depending on brush speed.
Esfumaçar

Enabling Smudge makes the brush «smudge» (or «smear») existing colors on the surface as it moves. The strength of this effect can be defined from the Smudge Strength property.

Even when smudge is enabled brush still does its normal paint effect. If you want a purely smudging brush use zero alpha. It is also possible to have Erase option enabled together with smudge.

Ondas

Referência

Type:Pincel
Panel:Physics ‣ Dynamic Paint ‣ Waves

This panel is used to adjust brush influence to «Wave» surfaces.

Tipo de onda

Select what effect the brush creates in the wave simulation.

Alteração de profundidade

This option makes brush create waves when the intersection depth with the surface is changed on that point. If the brush remains still, it will not have influence.

Using a negative «Factor» with this type can create a nice looking «wake» for moving objects like ships.

Obstáculo
Constantly affects surface whenever intersecting. Waves are also reflected off this brush type. However, due the nature of wave simulation algorithm this type creates an unnatural «dent» in the surface if brush remains still.
Força
Directly affects the velocity of wave motion. Therefore the effect is not one-to-one with brush intersection depth, yet the force strength depends on it.
Somente refletir
This type has no visible effect on the surface alone but reflects waves that are already on the surface.
Fator
Adjusts how strongly brush «depth» affects the simulation. You can also use negative values to make brush pull water up instead of down.
Limitar ondas
In some cases the brush goes very deep inside the surface messing whole simulation up. You can use this setting to «limit» influence to only certain depth.