Solidificar

The Solidify modifier takes the surface of any mesh and adds depth, thickness to it.

Opções

The Solidify modifier in simple mode.

The Solidify modifier in complex mode.

Mode

Simples

This is the default solidify algorithm, which simply extrudes the geometry. This algorithm does not work on geometry where edges have more than two adjacent faces.

Importante

If the normals of adjacent faces don’t point into the same general direction, simple mode will not be able to solidify the boundary between those. This happens if the normals are not recalculated or for example on one-sided surfaces like a Möbius strip.

Complex

This is a solidify algorithm which can handle every geometric situation to guarantee a manifold output geometry. This algorithm is able to solidify shapes like Möbius strips, Klein bottles, architectural wall layouts and many more which the Simple Mode isn’t able to do. If the special cases are not present it is recommended to choose Simple because the extra logic makes this algorithm much slower.

Nota

There are no options for crease in the Modifier tab because crease is handled in a dynamic way. The modifier will transfer the creases of the original mesh in a smart way to the output mesh to work with the Subdivision Surface modifier.

Thickness Mode Complex Mode

Choose the kind of thickness handling (thickness solver).

Different thickness options on a non-manifold mesh.

Fixo

This is similar to Simple Mode without Even Thickness. The new vertices are always in a fixed distance to the old ones.

Uniformizar

This is similar to Simple Mode with Even Thickness and High Quality Normals. It adjusts for sharp corners, but may not always work when more than three faces come together.

Restrições

This is a more advanced model to try to always get the optimal thickness everywhere. For up to three faces it is always guaranteed to find an optimal solution.

Boundary Complex Mode

Choose the kind of boundary that suits the model the most.

Different boundary options with a matCap.

None

No boundary fix is applied. Results are stable.

Round

Adjusts the boundary for an opening to face inwards (like a hole in an egg).

Flat

Adjusts the boundary of a planar opening to be a flat (like a cut sphere).

Espessura

A profundidade a ser solidificada.

Importante

The modifier thickness is calculated using local vertex coordinates. If the object has a non-uniform scale, the thickness will vary on different sides of the object.

To fix this, either Apply or Clear the scale.

Deslocamento

A value between (-1 to 1) to locate the solidified output inside or outside the original mesh. The inside and outside is determined by the face normals. Set to 0.0, the solidified output will be centered on the original mesh.

Even Thickness Simple Mode

Mantém a espessura ajustando cantos agudos. Às vezes melhora a qualidade mas também aumenta o tempo de computação.

Merge Threshold Complex Mode

Distance within which degenerated geometry is merged.

Aros

Preencher

Preenche os vazios entre as arestas internas e externas.

Somente os aros

In Simple Mode: Will not extrude surfaces parallel to the original one, but instead will only add the perpendicular rim.

In Complex Mode: Will only leave the generated perpendicular rim.

Nota

Fill and Only Rim only make a difference on Non-manifold objects, since the rims are generated from the borders of the original geometry.

Vertex Group

The weights of the selected vertex group are multiplied onto the Thickness, so vertices with lower weights will be less thick. The vertices which are not part of the vertex group will be used as if their weight was zero.

Invert

Reverses the vertex group weights, so that the used weight is one minus the actual weight.

Fator

Quanto os grupos de vértices são levados em consideração.

• On 0.0 , vertices with zero weight will have no thickness at all.

• Com 0.5 , vértices com peso zero terão metade da espessura dos que com peso total.

• On 1.0 , the weights are ignored and the Thickness value is used for every vertex.

Flat Faces Complex Mode

Use the minimal vertex weight assigned to the vertices of a face to make sure that new faces stay parallel to their original ones. This is slow, so disable it when it is not needed.

Nota

If the final thickness of a vertex is zero, it will still be solidified. Therefore creating duplicate geometry, which sometimes needs extra care.

Normais

Inverter as normais

Reverte as normais de toda geometria (tanto as superfícies internas como externas).

High Quality Normals Simple Mode

Normais são calculadas para produzir uma espessura mais uniforme. Às vezes melhora a qualidade mas também aumenta o tempo de computação.

Materials

Deslocamento de material

Choose a different material slot index to use for the new geometry. This is applied as an offset from the original material of the face from which it was solidified.

• Um valor 0 significa que irá usar o mesmo material.

• Um valor 1 significa que irá usar o material imediatamente abaixo do material original.

• Um valor de -2 significa que o material duas posições acima do material original será usado.

Isso é restrito aos materiais mais acima e mais abaixo da lista de materiais.

Aros

Similarmente, você pode fornecer outro material para as faces dos aros.

Edge Data

Inner Simple Mode

Set a crease to the inner edges.

Outer Simple Mode

Set a crease to the outer edges.

Rim Simple Mode

Set a crease to the rim.

Bevel Convex

Edge bevel weight to be added to outside edges.

Edges which will get creases marked.

Thickness Clamp

Clamp

A value between (0 to 2) to clamp offsets to avoid self-intersection. The amount is determined by the length of the shortest adjacent edge.

Limitar deslocamento.

Angle Clamp

If enabled clamping will also consider angles in the geometry, not only lengths.

Output Vertex Groups

Shell

Vertex group that the generated shell geometry will be weighted to. This allows you to use other modifiers to only affect the shell geometry by using a that modifier’s vertex group influence control.

Aros

Same as Shell Vertex Group, but for the generated rim geometry.

Known Limitations

Espessura uniforme

Solidify thickness is an approximation. While Even Thickness and High Quality Normals should yield good results, the final wall thickness is not guaranteed and may vary depending on the mesh topology. Especially for vertices with more than three adjacent faces.

In order to maintain a precise wall thickness in every case, we would need to add/remove faces on the offset shell, something this modifier does not do since this would add a lot of complexity. The best option to preserve wall thickness is complex mode with constraints thickness mode, but it is also not guaranteed to work perfect in every case.