Selecting

This page discusses specific selecting tools for curve objects in Edit Mode. The Curve Edit more also uses the general select tools used which are described in the interface section.

Curve selection in Edit Mode has fewer options than with meshes. Mainly this is, because there is only one selectable element type, the control points (no select mode needed here...). These points are a bit more complex than simple vertices, however, especially for Bézier curves, as there is the central vertex, and its two handles...

The basic tools are the same as with meshes, so you can select a simple control point with the LMB, add to current selection with Shift-LMB, Box Select B, and so on.

One word about the Bézier control points: when you select the main central vertex, the two handles are automatically selected too, so you can move it as a whole, without creating an angle in the curve. However, when you select a handle, only this vertex is selected, allowing you to modify this control vector...

Note that, unlike mesh edges, you cannot directly select a segment. Instead, select all of the control points that make up the segment you want to edit.

Select Menu

With curves, all "advanced" selection options are grouped in the Select menu of the 3D Viewport header.

All

Reference

Mode:

編輯模式

選單:

Select ‣ All

Shortcut:

A

Select all selectable elements.

Reference

Mode:

編輯模式

選單:

Select ‣ None

Shortcut:

Alt-A

Deselect all elements, but the active element stays the same.

Invert

Reference

Mode:

編輯模式

選單:

Select ‣ Invert

Shortcut:

Ctrl-I

Selects all the geometry that are not selected, and deselect currently selected components.

Box Select

Reference

Mode:

編輯模式

選單:

Select ‣ Box Select

Shortcut:

B

Interactive box selection.

Circle Select

Reference

Mode:

編輯模式

選單:

Select ‣ Circle Select

Shortcut:

C

Interactive circle selection.

Lasso Select

Reference

Mode:

編輯模式

選單:

Select ‣ Lasso Select

Shortcut:

Ctrl-Alt-LMB

See Select Lasso.

Select Random

Reference

Mode:

編輯模式

選單:

Select ‣ Select Random

Select Random control points.

百分比值(Percent)

Selects the defined percentage of control points.

Random Seed

Seed used by the pseudo-random number generator.

Action

Controls whether the operator Selects or Deselects control points.

Checker Deselect

Reference

Mode:

編輯模式

選單:

Select ‣ Checker Deselect

This tool applies an alternating selected/deselected checker pattern. This only works if you already have more than one control point selected.

It works by changing the current selection so that only every Nth control points will remain selected, starting from the active one.

Deselected

The number of deselected elements in each pattern repetition.

Selected

The number of selected elements in each pattern repetition.

偏移量(Offset)

Offset from the starting point.

Select More/Less

Reference

Mode:

編輯模式

選單:

Select ‣ More/Less

Shortcut:

Ctrl-NumpadPlus, Ctrl-NumpadMinus

Their purpose, based on the currently selected control points, is to reduce or enlarge this selection.

More

For each selected control point, select all its linked points (i.e. one or two...).

Less

For each selected control point, if all points linked to this point are selected, keep this one selected. Otherwise, deselect it.

This implies two points:

  1. When all control points of a curve are selected, nothing will happen (as for Less, all linked points are always selected, and of course, More cannot add any). Conversely, the same goes when no control points are selected.

  2. Second, these tools will never "go outside" of a curve (they will never "jump" to another curve in the same object).

Select Linked

Reference

Mode:

編輯模式

選單:

Select ‣ Select Linked

Shortcut:

L, Ctrl-L, Shift-L

L (or Ctrl-L for all) will add to the selection the cursor's nearest control point, and all the linked ones, i.e. all points belonging to the same curve. Note that for Bézier, using L with a handle selected will select the whole control point and all the linked ones.

Select Similar

Reference

Mode:

編輯模式

選單:

Select ‣ Select Similar

Shortcut:

Shift-G

Selects control points that have certain similar properties to the active one. The Adjust Last Operation panel provides several selection options:

Type
Type

Selects splines that have the same spline Type i.e. Bézier, NURBS or Poly.

Radius

Selects control points that have a similar Radius value.

權重

Selects all points that have a similar Weight value.

Direction

Selects control points that have a similar handles direction.

Compare

For quantitative properties, this property selects the type of comparison to between the two numerical values.

Equal:

Select items with the same value as the active item's chosen property.

Greater:

Select items with a larger value as the active item's chosen property.

Less:

Select items with a smaller value as the active item's chosen property.

Threshold

For quantitative properties, this property controls how close the property's values have to be in the comparison.

(De)select First/Last

Reference

Mode:

編輯模式

選單:

Select ‣ (De)select First, Select ‣ (De)select Last

These operators will toggle the selection of the first or last control point(s) of the curve(s) in the object. This is useful to quickly find the start of a curve (e.g. when using it as path...).

Select Next/Previous

Reference

Mode:

編輯模式

選單:

Select ‣ Select Next, Select ‣ Select Previous

These operators will select the next or previous control point(s), based on the current selection (i.e. the control points following or preceding the selected ones along the curve). In case of a cyclic curve, the first and last points are not considered as neighbors.

Pick Shortest Path

Reference

Mode:

編輯模式

選單:

Menu Search ‣ Pick Shortest Path

Shortcut:

Ctrl-LMB

Selects the curve segments between two control points: the active and the one under the cursor. In the case of a closed curve, the shortest path will be selected.