Loop Cut and Slide

Ссылка

Режим (mode):

Режим редактирования (edit mode)

Меню:

Edge ‣ Loop Cut and Slide

Горячая клавиша:

Ctrl-R

Loop Cut and Slide splits a loop of faces by inserting a new edge loop intersecting the chosen edge.

Использование

Инструмент является интерактивным и состоит из двух шагов:

  1. Предпросмотр будущего разреза

    После активации инструмента наведите курсор на нужное ребро. При наведении курсора на различные рёбра разрез будет отмечен пурпурной линией. Создаваемый контур разреза останавливается на полюсах (треугольниках и n-угольниках), где заканчивается существующая петля грани.

  2. Sliding the new Edge Loop

    Once an edge is chosen via LMB, you can move the mouse along the edge to determine where the new edge loop will be placed. This is identical to the Edge Slide tool. Clicking LMB again confirms and makes the cut at the pre-visualized location, or clicking RMB forces the cut to exactly 50%. This step is skipped when using multiple edge loops (see below).

../../../../_images/modeling_meshes_tools_loop_before.png

Сетка до вставки петли рёбер.

../../../../_images/modeling_meshes_tools_loop_preview.png

Предпросмотр расположения петли рёбер.

../../../../_images/modeling_meshes_tools_loop_placement.png

Интерактивное размещение петли рёбер между соседними петлями.

Опции (options)

These options are available while the tool is in use, and later in the Настроить последнюю операцию (adjust last operation) panel.

Number of Cuts Wheel or PageUp / PageDown

After activating the tool, but before confirming initial loop location, you can increase and decrease the number of cuts to create, by entering a number with the keyboard, scrolling Wheel or using PageUp and PageDown.

Примечание

When creating multiple loops, these cuts are uniformly distributed in the original face loop, and you will not be able to control their positions.

../../../../_images/modeling_meshes_editing_edge_loopcut-slide_multicut.png

Preview of multiple edge loops.

../../../../_images/modeling_meshes_editing_edge_loopcut-slide_multicut-after.png

Result of using multiple cuts.

Smoothness Alt-Wheel

Smoothing causes edge loops to be placed in an interpolated position, relative to the face it is added to, causing them to be shifted outwards or inwards by a given percentage, similar to the Subdivide Smooth tool. When not using smoothing, new vertices for the new edge loop are placed exactly on the preexisting edges. This keeps subdivided faces flat, but can distort geometry, particularly when using Subdivision Surfaces. Smoothing can help maintain the curvature of a surface once it is subdivided.

../../../../_images/modeling_meshes_editing_edge_loopcut-slide_unsmooth.png

Added edge loops without smoothing.

../../../../_images/modeling_meshes_editing_edge_loopcut-slide_smooth.png

Same edge loops, but with smoothing value.

Спад (falloff)

Falloff type for Smoothness, changes the shape of the profile.

Коэффициент (factor)

Position of the edge loop relative to the surrounding edge loops.

Even E

Only available for single edge loops. This matches the shape of the edge loop to one of the adjacent edge loops. (See Edge Slide tool for details.)

Flip F

When Even is enabled, this flips the target edge loop to match. (See Edge Slide tool for details.)

Ограничение (clamp)

Clamp within the edge extents.

Correct UVs

Корректирует соответствующие UV-координаты, если они существуют, чтобы избежать искажений изображения.