Speed Control

Speed Control time-warps the strip, making it play faster or slower than it normally would. A Global Speed less than 1.0 makes the strip play slower; greater than 1.0 makes it play faster. Playing faster means that some frames are skipped, and the strip will run out of frames before the end frame. When the strip runs out of frames to display, it will just keep repeating the last one; action will appear to freeze. To avoid this, position the next strip under the original at a point where you want the motion to continue.

Options

Stretch to Input Strip Length

Automatically calculates the Speed Factor based on the length of the input strip. So if you make a strip 1/2 the original size the sequence will play back at 2 times the speed.

Use as Speed

Calculates the scale value based on a Speed Factor.

Note

Vous devrez réajuster manuellement la longueur de la bande en conséquence.

Speed Factor

Multiplies the current speed of the sequence by this value. So, a value of 0.5 will make the sequence half as fast while 2 would make the sequence twice as fast.

Frame Number

Specifies a frame to remap the current frame to, for example, setting this value to 50 displays the 50th frame. This can then be manually keyframed to recreate the animation.

Scale to Length

Maps the frame range on a 0-1 scale. For example, using this and a Frame Number of 0.5 will select the frame halfway through the sequence.

Multiply Speed

A multiplier applied after all other calculations.

Frame Interpolation

Fondu enchaîné entre les images pour réduire le déchirement de l’écran lorsque la vitesse est inférieure à la fréquence d’images d’origine.

Exemples

Création d’un effet de ralenti (Slow-Motion)

Suppose you want to slow your strip down. You need to affect the speed of the video clip without affecting the overall frame rate. Select the clip and Add ‣ Effect ‣ Speed Control effect strip. Click to drop it and press N to get the Properties. Uncheck the Stretch to input strip length option in the Effect Strip section. Set the Speed factor to be the factor by which you want to adjust the speed. To cut the displayed speed by 50%, enter 0.5. Now, a 275-frame clip will play at half speed, and thus display only the first 137 frames.

Si vous voulez afficher les trames restantes à vitesse lente après l’affichage du premier ensemble, doublez la longueur de la bande source (puisque les limites de la bande d’effet sont contrôlées par leurs bandes sources). Si vous utilisez un facteur de vitesse autre que 0,5 alors utilisez la formule :

nouvelle_longueur = longueur_réelle / facteur_speed

Ce faisant, définissez votre rendu pour animer (dans cet exemple) l’ensemble des 550 trames.

Images clés de la commande de vitesse

Keyframing the Frame number.

To get even finer control over your clip timing, you can use curves! While it is possible to keyframe the Speed factor, usually you want to keyframe the Frame number directly.

Uncheck Stretch to input strip length and uncheck Use as speed. You now have a Frame number field which you can keyframe. If you want the strip to animate at all you will have to insert some keyframes, otherwise it will look like a still. In most cases you will want to use the Graph editor view to set the curve interpolation to Linear since the default Bézier will rarely be what you want.

Astuce

Si vous choisissez d’utiliser l’image clé du facteur Speed à la place, souvenez-vous de Tout Actualiser (Refresh All) ou les changements ne prendront pas effet.

Modification des fréquence de trames vidéo

You can use the speed control to change the frame rate in frames per second (fps) of a video. If you are rendering your video to a sequence set, you can effectively increase or decrease the number of individual image files created, by using a Global Speed value less than or greater than one, respectively. For example, if you captured a five-minute video at 30 fps and wanted to transfer that to film, which runs at 24 fps, you would enter a Global Speed of 30/24, or 1.25 (and Enable Frame Blending to give that film blur feel). Instead of producing 5 × 60 × 30 = 9000 frames, Blender would produce 9000 / 1.25 = 7200 = 5 × 60 × 24 frames. In this case, you set a start = 1 and end = 7200, set your Format output to jpeg 30fps, and image files 0001.jpg through 7200.jpg would be rendered out, but those images cover the entire 9000 frames. The image file 7200.jpg is the same at frame 9000. When you read those images back into your film blend-file at 24 fps, the strip will last exactly 5 minutes.