Editing(編集)
Transform(トランスフォーム)
(未稿)。
Snap(スナップ)
(未稿)。
Bake Action
参照
- Editor(エディター):
Nonlinear Animation(ノンリニアアニメーション)
- Menu(メニュー):
参照
- Editor(エディター):
3D Viewport(3Dビューポート)
- Mode(モード):
Object and Pose Modes
- Menu(メニュー):
The final motion of objects or bones depends not only on the keyframed animation, but also on any active F-Curve modifiers, drivers, and constraints. On each frame of all the scene's frames, the Bake Action operator computes the final animation of the selected objects or bones with all those modifiers, drivers, and constraints applied, and keyframes the result.
This can be useful for adding deviation to a cyclic action like a Walk Cycle, or to create a keyframe animation created from drivers or constraints.
Duplicate(複製)
参照
- Menu(メニュー):
Creates a new instance of the selected strips with a copy of the action.
Linked Duplicate(リンク複製)
参照
- Menu(メニュー):
- ショートカットキー:
Alt-D
The contents of one Action strip can be instanced multiple times. To instance another strip, select a strip, go to . It will uses the same action as the selected strips.
Now, when any strip is tweaked, the others will change too. If a strip other than the original is tweaked, the original will turn to red.
リンク複製されたストリップを編集。
Split Strips
(未稿)。
Delete Strips
(未稿)。
Delete Tracks(トラックを削除)
(未稿)。
Toggle Muting(ミュートを切替え)
(未稿)。
Apply Scale(スケールを適用)
(未稿)。
Clear Scale(拡大縮小をクリア)
(未稿)。
Sync Action Length(アクションの長さに同期)
(未稿)。
Make Single User(シングルユーザー化)
参照
- Menu(メニュー):
- ショートカットキー:
U
This tool ensures that none of the selected strips use an action which is also used by any other strips.
注釈
これは、再帰的にはメタストリップ内に進みません。
Swap Strips(ストリップを交換)
(未稿)。
Move Strips Up
(未稿)。
Move Strips Down
(未稿)。
Track Ordering
(未稿)。
Remove Empty Animation Data(空のアニメーションデータを削除)
参照
- Menu(メニュー):
This operator removes AnimData data-blocks (restricted to only those which are visible in the animation editor where it is run from) which are "empty" (i.e. that is, have no active action, drivers, and NLA tracks or strips).
It is sometimes possible to end up with a lot of data-blocks which have old and unused Animation Data containers still attached. This most commonly happens when doing motion graphics work (i.e. when some linked-in objects may have previously been used to develop a set of reusable assets), and is particularly distracting in the NLA Editor.
Start Editing Stashed Action(保留アクションの編集を開始)
参照
- Menu(メニュー):
- ショートカットキー:
Shift-Tab
It will enter and exit Tweak Mode as usual, but will also make sure that the action can be edited in isolation (by flagging the NLA track that the action strip comes from as being "solo"). This is useful for editing stashed actions, without the rest of the NLA Stack interfering.
When you finished editing the strip, simply go to or press Shift-Tab.
NLAモードのストリップ。 |
調整モードのストリップ。 |
Start Tweaking Strips Actions (Full Stack)
参照
- Menu(メニュー):
Allows you to edit the contents of the strip without disabling all the tracks above the tweaked strip. This allows keyframing to work as expected, and preserves the pose that you visually keyed.
When you finished editing the strip, simply go to or press Tab.
注釈
For transitions above the tweaked strip, keyframe remapping will fail for channel values that are affected by the transition. A work around is to tweak the active strip without evaluating the upper NLA stack.
Start Tweaking Strips Actions (Lower Stack)
参照
- Menu(メニュー):
- ショートカットキー:
Tab
The contents of Action strips can be edited, but you must be in Tweak Mode to do so. The keyframes of the action can then be edited in the Dope Sheet.
When you finished editing the strip, simply go to or press Tab.