Girar¶
Referência
| Mode: | Edit Mode |
|---|---|
| Panel: | |
| Hotkey: | Alt-R |
The Spin tool extrudes (or duplicates it if the selection is manifold) the selected elements, rotating around a specific point and axis.
Use the tool to create the sort of objects that you would produce on a lathe (this tool is often called a «lathe»-tool or a «sweep»-tool in the literature, for this reason). In fact, it does a sort of circular extrusion of your selected elements, centered on the 3D cursor, and around the axis perpendicular to the working view…
- The point of view will determine around which axis the extrusion spins…
- A posição do cursor 3D será o centro da rotação.
Opções¶
- Passos
- Specifies how many copies will be extruded along the «sweep».
- Duplicate
- When enabled, will keep the original selected elements as separated islands in the mesh (i.e. unlinked to the result of the spin extrusion).
- Ângulo
- Specifies the angle «swept» by this tool, in degrees (e.g. set it to 180 for half a turn).
- Auto Merge
- Automatically merges the first a last duplicates, if they make a full revolution which results in overlapping geometry.
- Flip Normals
- Reverses the normal’s direction for any resulting geometry.
- Centro
- Specifies the center of the spin. By default it uses the cursor position.
- Eixos
- Specify the spin axis as a vector. By default it uses the view axis (viewport).
Exemplo¶
Perfil de vidro.
First, create a mesh representing the profile of your object. If you are modeling a hollow object, it is a good idea to thicken the outline. Fig. Perfil de vidro. shows the profile for a wine glass we will model as a demonstration.
Go to Edit Mode and select all the vertices of the Profile with A.
We will be rotating the object around the cursor in the top view, so switch to the top view with Numpad7.
Glass profile, top view in Edit Mode, just before spinning.
Place the cursor along the center of the profile by selecting one of the vertices along the center, and snapping the 3D cursor to that location with . (Fig. Glass profile, top view in Edit Mode, just before spinning.) shows the wine glass profile from top view, with the cursor correctly positioned.
Click the Spin button. If you have more than one 3D View open, the cursor will change to an arrow with a question mark and you will have to click in the area containing the top view before continuing. If you have only one 3D View open, the spin will happen immediately. Fig. Spun profile. shows the result of a successful spin.
Duplicate¶
Resultado da operação de girar. |
Result of Dupli enabled. |
Fundir duplicatas¶
Duplicação de vértices.
The spin operation leaves duplicate vertices along the profile. You can select all vertices at the seam with Box select B (shown in Fig. Duplicação de vértices.) and perform a Merge by Distance operation.
Notice the selected vertex count before and after the Merge by Distance operation
Vertex count after removing doubles. If all goes well, the final vertex count
(38 in this example) should match the number of the original profile noted in
.
If not, some vertices were missed and you will need to weld them manually.
Or, worse, too many vertices will have been merged.
Nota
Merging Two Vertices into One
To merge (weld) two vertices together, select both of them by Shift-RMB clicking on them. Press S to start scaling and hold down Ctrl while scaling to scale the points down to 0 units in the X, Y and Z axis. LMB to complete the scaling operation and click the Merge by Distance button in the Toolbar in Edit Mode (also available with ).
Alternatively, you can use from the same Specials menu (or Alt-M). Then, in the new pop-up menu, choose whether the merged vertex will be at the center of the selected vertices or at the 3D cursor. The first choice is better in our case!
Recalcular normais¶
All that remains now is to recalculate the normals to the outside by selecting all vertices, pressing Ctrl-N and validating Recalculate Normals Outside in the pop-up menu.