Editing – Редагування

Transform – Трансформа

Todo.

Snap – Підхоп

Todo.

Bake Action – Запекти Дію

Reference – Довідка

Editor – Редактор:

Nonlinear Animation – Нелінійна Анімація

Menu – Меню:

Edit ‣ Bake Action

Reference – Довідка

Editor – Редактор:

3D Viewport – 3D Оглядвікно

Mode – Режим:

Object and Pose Modes – Режими Об’єкта та Пози

Menu – Меню:

Header ‣ Object Animation ‣ Bake Action…

The final motion of objects or bones depends not only on the keyframed animation, but also on any active F-Curve modifiers, drivers, and constraints. On each frame of all the scene’s frames, the Bake Action operator computes the final animation of the selected objects or bones with all those modifiers, drivers, and constraints applied, and keyframes the result.

This can be useful for adding deviation to a cyclic action like a Walk Cycle, or to create a keyframe animation created from drivers or constraints.

Duplicate – Дублювання

Reference – Довідка

Menu – Меню:

Edit ‣ Duplicate

Creates a new instance of the selected strips with a copy of the action.

Linked Duplicate – Пов’язане Дублювання

Reference – Довідка

Menu – Меню:

Edit ‣ Linked Duplicate

Shortcut – Шоткат:

Alt-D

The contents of one Action strip can be instanced multiple times. To instance another strip, select a strip, go to Edit ‣ Linked Duplicate. It will uses the same action as the selected strips.

Now, when any strip is tweaked, the others will change too. If a strip other than the original is tweaked, the original will turn to red.

Пов’язано дубльована смужка редагується.

Split Strips

Todo.

Delete Strips

Todo.

Delete Tracks – Видалення Відстежень

Todo.

Toggle Muting – Перемкнення Приглушення

Todo.

Apply Scale – Застосування Масштабу

Todo.

Clear Scale – Зчищення Масштабу

Todo.

Sync Action Length – Синхрон Тривалості Дії

Todo.

Make Single User – Зроблення Однокористувацьким

Reference – Довідка

Menu – Меню:

Edit ‣ Make Single User

Shortcut – Шоткат:

U

This tool ensures that none of the selected strips use an action which is also used by any other strips.

Примітка

Це рекурсивно не входить всередину мета смужок.

Swap Strips – Обмін Смужок

Todo.

Move Strips Up

Todo.

Move Strips Down

Todo.

Track Ordering

Todo.

Remove Empty Animation Data – Вилучення Порожніх Даних Анімації

Reference – Довідка

Menu – Меню:

Edit ‣ Remove Empty Animation Data

This operator removes AnimData data-blocks (restricted to only those which are visible in the animation editor where it is run from) which are «empty» (i.e. that is, have no active action, drivers, and NLA tracks or strips).

It is sometimes possible to end up with a lot of data-blocks which have old and unused Animation Data containers still attached. This most commonly happens when doing motion graphics work (i.e. when some linked-in objects may have previously been used to develop a set of reusable assets), and is particularly distracting in the NLA Editor.

Start Editing Stashed Action – Старт Редагування Запасеної Дії

Reference – Довідка

Menu – Меню:

Edit ‣ Start Editing Stashed Action

Shortcut – Шоткат:

Shift-Tab

It will enter and exit Tweak Mode as usual, but will also make sure that the action can be edited in isolation (by flagging the NLA track that the action strip comes from as being «solo»). This is useful for editing stashed actions, without the rest of the NLA Stack interfering.

When you finished editing the strip, simply go to Edit ‣ Stop Editing Stashed Action or press Shift-Tab.

Смужка у режимі НЛА – NLA.

Смужка у режимі Підправлення – Tweak.

Start Tweaking Strips Actions (Full Stack)

Reference – Довідка

Menu – Меню:

Edit ‣ Start Tweaking Strips Actions (Full Stack)

Allows you to edit the contents of the strip without disabling all the tracks above the tweaked strip. This allows keyframing to work as expected, and preserves the pose that you visually keyed.

When you finished editing the strip, simply go to Edit ‣ Stop Tweaking Strips Actions or press Tab.

Примітка

For transitions above the tweaked strip, keyframe remapping will fail for channel values that are affected by the transition. A work around is to tweak the active strip without evaluating the upper NLA stack.

Start Tweaking Strips Actions (Lower Stack)

Reference – Довідка

Menu – Меню:

Edit ‣ Start Tweaking Strips Actions (Lower Stack)

Shortcut – Шоткат:

Tab

The contents of Action strips can be edited, but you must be in Tweak Mode to do so. The keyframes of the action can then be edited in the Dope Sheet.

When you finished editing the strip, simply go to Edit ‣ Stop Tweaking Strips Actions or press Tab.