Ràng Buộc Biến Hóa (Transformation Constraint)¶
This constraint is more complex and versatile than the other "transform" constraints. It allows you to map one type of transform properties (i.e. location, rotation or scale) of the target, to the same or another type of transform properties of the owner, within a given range of values (which might be different for each target and owner property). You can also switch between axes, and use the range values not as limits, but rather as "markers" to define a mapping between input (target) and output (owner) values.
So, e.g. you can use the position of the target along the X axis to control the rotation of the owner around the Z axis, stating that 1 unit along the target X axis corresponds to 10 units around the owner Z axis. Typical uses for this include gears (see note below), and rotation based on location setups.
Các Tùy Chọn (Options)¶
Transformation panel.¶
- Mục Tiêu (Target)
ID Dữ Liệu (Data ID) used to select the constraints target, and is not functional (red state) when it has none. See common constraint properties for more information.
- Ngoại Suy (Extrapolate)
By default, the Min and Max values bound the input and output values; all values outside these ranges are clipped to them. When you enable this button, the Min and Max values are no longer strict limits, but rather "markers" defining a proportional (linear) mapping between input and corresponding output values. Let us illustrate that with two graphs Fig. Các nguyên tắc ngoại suy.. In these pictures, the input range (in abscissa) is set to (1.0 to 4.0), and its corresponding output range (in ordinate), to (1.0 to 2.0). The yellow curve represents the mapping between input and output.
Các nguyên tắc ngoại suy.¶ 
Extrapolate disabled: the output values are bounded inside the (1.0 to 2.0) range.¶
Extrapolate enabled: the output values are "free" to proportionally follow the input ones.¶
- Mục Tiêu/Chủ Nhân (Target/Owner)
Standard conversion between spaces. See common constraint properties for more information.
- Tác Động/Ảnh Hưởng (Influence)
Controls the percentage of affect the constraint has on the object. See common constraint properties for more information.
Ánh Xạ Từ (Map From)¶
It contains the input (from target) settings.
- Vị Trí, Xoay Chiều, Tỷ Lệ (Location, Rotation, Scale)
The radio buttons allow you to select which type of property to use.
- Chế Độ [Xoay Chiều] (Mode [Rotation])
Allows specifying the type of rotation input to use, including different Euler orders, Quaternion, and other Rotation Channel Modes. Defaults to using the Euler order of the constraint owner.
In the Quaternion mode the channels are converted to weighted angles in the same way as the swing angles of the Swing and X/Y/Z Twist modes.
- X/Y/Z Tối Thiểu, Tối Đa (X/Y/Z Min, Max)
Independently for each axis (X, Y, and Z) the min and max number fields control the lower and upper bounds of the input value range. Note that if a min value is higher than its corresponding max value, the constraint behaves as if it had the same value as the max one.
Ánh Xạ Tới (Map To)¶
It contains the output (to owner) settings.
- Vị Trí, Xoay Chiều, Tỷ Lệ (Location, Rotation, Scale)
The three radio buttons allow you to select which type of property to control.
- Thứ Tự [Xoay Chiều] (Order [Rotation])
For rotation, allows specifying which Euler order to use during evaluation of the constraint. Defaults to using the order of the constraint owner.
- Trục Nguồn X/Y/Z (X/Y/Z Source Axis)
The three axis selectors allow you to select which input axis to map to, respectively (from top to bottom), the X, Y and Z output (owner) axes.
- Tối Thiểu, Tối Đa (Min, Max)
The Min and Max number fields control the lower and upper bounds of the output value range, independently for each mapped axis. Note that if a min value is higher than its corresponding max value, the constraint behaves as if it had the same value as the max one.
- Hòa Trộn (Mix)
Specifies how the result of the constraint is combined with the existing transformation. The set of available choices varies based on the type of transformation.
- Thay Thế (Replace)
The result of the constraint replaces the existing transformation.
- Nhân [Tỷ Lệ] (Multiply [Scale])
The new values are multiplied with the existing axis values.
- Thêm [Vị Trí, Xoay Chiều] (Add [Location, Rotation])
The new values are added to the existing axis values.
- Trước cái Cũ [Xoay Chiều] (Before Original [Rotation])
The new rotation is added before the existing rotation, as if it was applied to a parent of the constraint owner.
- Sau cái Cũ [Xoay Chiều] (After Original [Rotation])
The new rotation is added after the existing rotation, as if it was applied to a child of the constraint owner.
Ghi chú
For historical reasons, the Mix mode defaults to Add for location and rotation, and Replace for scale.
When using the rotation transform properties of the target as input, whatever the real values are, the constraint will always "take them back" into the (-180 to 180) range. E.g. if the target has a rotation of 420 degrees around its X axis, the values used as X input by the constraint will be:
\(((420 + 180) modulo 360) - 180 = 60 - ...\)
This is why this constraint is not really suited for gears!
Similarly, when using the scale transform properties of the target as input, whatever the real values are, the constraint will always take their absolute values (i.e. invert negative ones).
When a min value is higher than its corresponding max one, both are considered equal to the max one. This implies you cannot create "reversed" mappings...