Chọn Cái Đã Kết Nối
Kết Nối
Tham Chiếu
- Chế Độ
Chế Độ Biên Soạn
- Trình Đơn
- Tổ Hợp Phím Tắt
Ctrl-L
Select geometry connected to already selected elements. This is often useful when a mesh has disconnected, overlapping parts, where isolating it any other way would be tedious. To give more control, you can also enable delimiters in the Điều Chỉnh Thao Tác Trước Đây panel, so the selection is constrained by seams, sharp edges, materials or UV islands.
With Pick Linked you can also select connected geometry directly under the cursor, using the L shortcut to select or Shift-L to deselect linked. This works differently in that it uses the geometry under the cursor instead of the existing selection.
Đường Ngắn Nhất
Tham Chiếu
- Chế Độ
Chế Độ Biên Soạn
- Trình Đơn
- Tổ Hợp Phím Tắt
Hòa Trộn Ctrl-0
Select a face or vertex path with Ctrl-LMB.
Selects all geometry along the shortest path from the active vertex, edge, or face to the one which was selected.
- Edge Tag (in Edge select mode only)
This select button indicates what should be done when selecting a vertex path with Ctrl-LMB:
- Chọn
Just selects all the edges in the path.
- Nhãn Đường Khâu
Marks all edges in the path as seams for UV unwrapping.
- Nhãn Sắc Nhọn
Marks all edges in the path as sharp for the Edge Split Modifier.
- Nhãn Nếp Gấp
Marks all edges in the path as creases for the Subdivision Surface Modifier, with weight 1.0.
- Nhãn Bo Tròn
Gives bevel weight 1.0 (for the Bevel Modifier) to all edges in the path.
- Nhãn Dấu Cạnh PCTD
Marks all edges in the path as Freestyle edges.
- Bước Bậc Thang theo Bề Mặt
Supports diagonal paths for vertices and faces, and selects edge rings with edges.
- Khoảng cách Cấu Trúc Liên Kết
Only takes into account the number of edges of the path and not the length of the edges to calculate the distances.
- Phủ Kín Vùng Shift-Ctrl-NCT (LMB)
Selects all elements in the shortest paths from the active selection to the clicked area.
- Các Tùy Chọn về Bỏ Chọn So Le
Allows to quickly select alternate elements in a path.
- Số Phần Tử Không Chọn
The number of deselected elements in the repetitive sequence.
- Cái được Chọn
The number of selected elements in the repetitive sequence.
- Dịch Chuyển
Dịch chuyển từ điểm khởi đầu.
Các Mặt Phẳng Kết Nối
Tham Chiếu
- Chế Độ
Chế Độ Biên Soạn
- Trình Đơn
Selects all connected faces with a similar angle.
- Độ Sắc Nhọn
Select connected faces with a reference angle less than the value specified.
Looking at the image above, when at least one face is selected (as seen on the left), Linked Flat Faces will select all connecting faces that lie on the same or similar plane (as shown in the middle image). If the corners are smoothed, those faces are no longer lined up with the selected faces. At this point, increasing the Sharpness value in the tool options could include the smoothed faces.