Phân Chia Vòng Mạch và Trượt Đẩy

Tham Chiếu

Chế Độ

Chế Độ Biên Soạn

Trình Đơn

Thanh bên (Sidebar) -> thẻ Kiến Tạo (Create tab)

Tổ Hợp Phím Tắt

Ctrl-R

Loop Cut and Slide splits a loop of faces by inserting a new edge loop intersecting the chosen edge.

Sử Dụng

The tool is interactive and has two steps:

  1. Pre-Visualizing the Cut

    After the tool is activated, move the cursor over a desired edge. The cut to be made is marked with a magenta colored line as you move the mouse over the various edges. The to be created edge loop stops at the poles (tris and n-gons) where the existing face loop terminates.

  2. Sliding the new Edge Loop

    Once an edge is chosen via LMB, you can move the mouse along the edge to determine where the new edge loop will be placed. This is identical to the Edge Slide tool. Clicking LMB again confirms and makes the cut at the pre-visualized location, or clicking RMB forces the cut to exactly 50%. This step is skipped when using multiple edge loops (see below).

../../../../_images/modeling_meshes_tools_loop_before.png

Mesh before inserting edge loop.
../../../../_images/modeling_meshes_tools_loop_preview.png

Preview of edge loop location.
../../../../_images/modeling_meshes_tools_loop_placement.png

Interactive placement of edge loop between adjacent loops.

Tùy Chọn

These options are available while the tool is in use, and later in the Điều Chỉnh Thao Tác Trước Đây panel.

Số Đường Cắt Bánh Xe (Wheel) hoặc Trang Lên (PageUp) / Trang Xuống (PageDown)

After activating the tool, but before confirming initial loop location, you can increase and decrease the number of cuts to create, by entering a number with the keyboard, scrolling Wheel or using PageUp and PageDown.

Ghi chú

When creating multiple loops, these cuts are uniformly distributed in the original face loop, and you will not be able to control their positions.

../../../../_images/modeling_meshes_editing_edge_loopcut-slide_multicut.png

Preview of multiple edge loops.
../../../../_images/modeling_meshes_editing_edge_loopcut-slide_multicut-after.png

Result of using multiple cuts.
Độ Mềm Mại Alt-Bánh Xe (Wheel)

Smoothing causes edge loops to be placed in an interpolated position, relative to the face it is added to, causing them to be shifted outwards or inwards by a given percentage, similar to the Subdivide Smooth tool. When not using smoothing, new vertices for the new edge loop are placed exactly on the pre-existing edges. This keeps subdivided faces flat, but can distort geometry, particularly when using Subdivision Surfaces. Smoothing can help maintain the curvature of a surface once it is subdivided.

../../../../_images/modeling_meshes_editing_edge_loopcut-slide_unsmooth.png

Added edge loops without smoothing.
../../../../_images/modeling_meshes_editing_edge_loopcut-slide_smooth.png

Same edge loops, but with smoothing value.
Suy Giảm Dần

Falloff type for Smoothness, changes the shape of the profile.

Hệ Số

Position of the edge loop relative to the surrounding edge loops.

Đồng Đều E

Only available for single edge loops. This matches the shape of the edge loop to one of the adjacent edge loops. (See Edge Slide tool for details.)

Đảo Lật F

When Even is enabled, this flips the target edge loop to match. (See Edge Slide tool for details.)

Hạn Định

Hạn định nội trong phạm vi của cạnh.

Chỉnh Sửa UV

Corrects the corresponding UV coordinates, if these exist, to avoid image distortions.