Fill Tool

Reference

Mode:

Draw Mode

Tool:

Toolbar ‣ Fill

The Fill tool is used to automatically fill closed strokes areas.

Brush Settings

You can also configure the brush main settings exposed on the Tool Settings for convenience.

Direction Ctrl

The portion of area to fill.

Normal:

Fills the area inside the shape under the cursor.

Inverted:

Fills the area outside the shape under the cursor.

Precision

Multiplier for fill boundary accuracy. Higher values are more accurate but slower.

Dilate/Contract

Size in pixels to expand or shrink the fill area from the strokes boundary.

Thickness

The thickness radius of the boundary stroke in pixels.

Advanced

Boundary

Sets the type of fill boundary limits calculation to perform.

All:

Use the thickness of the strokes and the editing lines together.

Strokes:

Use only the thickness of the strokes (ignore edit lines).

Edit Lines:

Use only the edit lines (ignore strokes).

Show Lines (eye icon)

Toggle show auxiliary lines to see the fill boundary.

Layers

Determines which Layers are used for boundary strokes.

Visible:

Calculates boundaries based on all visible layers.

Aktiv:

Calculates boundaries based on the active layer.

Layer Above:

Calculates boundaries based on the layer above the active layer.

Layer Below:

Calculates boundaries based on the layer below the active layer.

All Above:

Calculates boundaries based on all layers above the active layer.

All Below:

Calculates boundaries based on all layers below the active layer.

Simplify

Number of simplify steps to apply to the boundary line. Higher values reduce the accuracy of the final filled area.

Ignore Transparent

When enabled, strokes with transparency does not take into account on fill boundary calculations.

The value slider controls the threshold to consider a material transparent.

Limit to Viewport

When enabled, fill only visible areas in the viewport.

Gap Closure

Gap closure lines are automatic temporarily lines that help to close gaps on the strokes.

Size

Control the Size of the line extension or the circumference to use to calculate the lines that will close the gaps.

Mode S

Sets the type of Gap closure method to use.

Radius:

Uses the Radius of circumference of opened nearest points to calculate a line that close the gap.

Extend:

Extends the opened strokes to close gaps.

Visual Aids

Toggle show closure lines helper.

Strokes Collision D

Check if extend lines collide with strokes, stopping the extension if a collision is detected.

Only Collide Lines

Use for closing gaps only if the extend strokes collide.

Usage

Selecting a Brush and Material

In the Tool Settings select the brush, material and color type to use with the tool. The Fill tool uses Fill Brush types. See Brush Settings for more information.

Filling Areas

Click LMB in a closed stroke area. The tool will automatically calculate the boundary and create a new closed stroke filled with the material selected.

../../../../_images/grease-pencil_modes_draw_tools_fill_example-01.png

Original Drawing.

../../../../_images/grease-pencil_modes_draw_tools_fill_example-02.png

Use the fill tool to leak materials on closed areas.

../../../../_images/grease-pencil_modes_draw_tools_fill_example-03.png

Final filled drawing.

Boundary Strokes

If you have a large gap in an area that you want fill, you can add boundary strokes manually, a temporary auxiliary lines for closing open shapes. To create a boundary stroke use Alt-LMB and draw a line to close the desired area.

../../../../_images/grease-pencil_modes_draw_tools_fill_boundary-strokes-01.png

Original drawing.

../../../../_images/grease-pencil_modes_draw_tools_fill_boundary-strokes-02.png

Add boundary strokes to close open areas (red lines).

../../../../_images/grease-pencil_modes_draw_tools_fill_boundary-strokes-03.png

Use the Fill tool to leak material on the new closed area.

When you are satisfied with the fill result you can delete the boundary strokes using the Clean Up tool in the Grease Pencil Menu in Edit Mode.

Automatic Gap Closure

A more automatic way to close gaps in an area that you want fill is using temporarily helper lines. There are two method to use «Radius» or «Extend»

Radius use temporary auxiliary lines calculated from the radius of nearby open points to close open shapes. Set the size more than zero to control the circle size over opened points (the circle will disappear when the line close the gap). Click over the area you want to be filled and change the length of the strokes using PageUp PageDown or Wheel. When you are satisfied with the length and you are sure the temporarily strokes cross each other, click again to fill the area.

../../../../_images/grease-pencil_modes_draw_tools_fill_extended-strokes-01.png

Original Drawing.

../../../../_images/grease-pencil_modes_draw_tools_fill_radius-02.png

Use Radius mode to close open areas (Red circles and cyan lines).

../../../../_images/grease-pencil_modes_draw_tools_fill_radius-03.png

Use Fill Tool to leak material on the new closed area.

Extend use temporary auxiliary lines extending the actual strokes ends for closing open shapes. Set the size more than zero to use the extended lines, click over the area you want to be filled and change the length of the strokes using PageUp/PageDown, Wheel or a pen’s MMB. When you are satisfied with the length and you are sure the temporarily strokes cross each other, click again to fill the area.

../../../../_images/grease-pencil_modes_draw_tools_fill_extended-strokes-01.png

Original Drawing.

../../../../_images/grease-pencil_modes_draw_tools_fill_extended-strokes-02.png

Use Extend mode to close open areas (cyan lines).

../../../../_images/grease-pencil_modes_draw_tools_fill_extended-strokes-03.png

Use Fill Tool to leak material on the new closed area.

Switch to Draw Tool

Use Ctrl-LMB to change temporary to the active draw tool. For example to manually cover small areas difficult to reach for the Fill tool. See Draw Tool for more information.