Yta

Omvandla

Referens

Läge:

Redigeringsläge

Meny:

Yta ‣ Transform

Tools for moving control points.

Flytta, rotera, skala

See Basic Transformations.

Sfär, skjuvning, böjning, tryck/drag, skevhet, slumpmässighet

See Mesh Transformations.

Flytta/skalera texturutrymme

See Texturutrymme.

Spegel

Referens

Läge:

Redigeringsläge

Meny:

Surface ‣ Mirror

Genväg:

Ctrl-M

See Spegel.

Fäst

Referens

Läge:

Redigeringsläge

Meny:

Surface ‣ Snap

Genväg:

Shift-S

See the Fäst menu, as well as the snapping options.

Snurra

Referens

Läge:

Redigeringsläge

Meny:

Yta ‣ Snurr

Similar to its mesh counterpart, this operator extrudes the selected control points several times along a circle that’s centered on the 3D-markör and parallel to the viewing plane. The weights of the new control points are set up to produce a circle, and the surface is marked as Cyclic, Bézier, and Endpoint in the extrusion direction (see Aktiv spline).

Lägg till duplikat

Referens

Läge:

Redigeringsläge

Meny:

Yta ‣ Lägg till duplikat

Genväg:

Shift-D

Duplicates the selected control points and creates a new surface based on them. The new control points are placed in the Move mode: move the mouse to bring them to the desired position, then click LMB to confirm. Alternatively, press RMB or Esc to keep them at their original position.

Note that the selected control points must form a single, valid sub grid. If this is not the case, the duplication will fail with an error.

Dela

Referens

Läge:

Redigeringsläge

Meny:

Yta ‣ Split

Genväg:

Y

Disconnects the selected sub grid from the rest of the surface, keeping it within the same Surface object. The control points at the border are duplicated so that both the original surface and the disconnected surface have them.

The sub grid must consist of one or more complete rows or columns of the surface grid.

Separera

Referens

Läge:

Redigeringsläge

Meny:

Yta ‣ Separat

Genväg:

P

Disconnects the selected sub grid from the rest of the surface and moves it into a new Surface object. The control points at the border are duplicated so that both the original surface and the disconnected surface have them.

The sub grid must consist of one or more complete rows or columns of the surface grid.

Växla Cyklisk

Referens

Läge:

Redigeringsläge

Meny:

Yta ‣ Växla cykliskt

Genväg:

Alt-C

Opens a popover menu with the options Cyclic U and Cyclic V. The surface is made cyclic (closed) or non-cyclic (open) in the corresponding direction.

If a surface is cyclic, the last row or column of its control point grid is connected back to the first. A cylinder is cyclic along either the U or V direction, while a sphere is cyclic along both.

Se även

The Cyclic settings are also in the Aktiv spline panel in the Sidebar.

Ställ in Spline-typ

Referens

Läge:

Redigeringsläge

Meny:

Yta ‣ Ställ in Spline-typ

Den här funktionen fungerar bara för Curves.

Visa/dölj

Referens

Läge:

Redigeringsläge

Meny:

Surface ‣ Show/Hide

Genväg:

H, Shift-H, Alt-H

Hides the selected or unselected control points, or unhides all hidden control points.

By default, unhiding control points adds them to the selection. To prevent this, uncheck the Select option in the Justera senaste operation panel.

Rensa

Referens

Läge:

Redigeringsläge

Meny:

Yta ‣ Rengöring

Den här funktionen fungerar bara för Curves.

Ta bort

Referens

Läge:

Redigeringsläge

Meny:

Yta ‣ Radera

Genväg:

X, Delete

Removes the selected Vertices (control points) or Segments (lines) from the surface. In both cases, the selection must consist of one or more complete rows or columns of the surface grid.

Hörn

Deletes the selected control points. The resulting gap is bridged with new grid lines so that the surface stays contiguous.

Segment

Deletes the lines and control points that lie between the outermost selected control points. The resulting gap is not bridged.

Lös upp vertikaler

Den här funktionen fungerar bara för Curves.

Before and after deleting a row of control points.