Select All by Trait (Alles Selecteren op Eigenschap)

Non Manifold

Reference (Referentie)

Mode (Modus):

Edit Mode (Bewerkingsmodus)

Menu:

Select ‣ Select All by Trait ‣ Non Manifold

Selects the non-manifold geometry of a mesh. This entry is only available in the Vertex and Edge selection modes.

Options (Opties)

Extend (Uitbreiden)

Adds to the current selection instead of replacing it.

Wire

Selects edges that do not belong to any face.

Boundaries (Grenzen)

Selects edges at boundaries and holes.

Multiple Faces (Meerdere Vlakken)

Selecteert randen die bij drie of meer vlakken horen.

Non Contiguous (Niet Aangrenzend)

Selecteert randen die behoren tot precies twee vlakken met tegenovergestelde normalen.

Vertices (Hoekpunten)

Selects vertices that are isolated, belong to an edge that’s a Wire or has Multiple Faces, or are the only vertex connecting two faces.

Loose Geometry (Losse Geometrie)

Reference (Referentie)

Mode (Modus):

Edit Mode (Bewerkingsmodus)

Menu:

Select ‣ Select All by Trait ‣ Loose Geometry

Depending on the selection mode, this operator selects vertices that are not part of any edge, edges that are not part of any face, or faces that do not share an edge with any other face.

Interior Faces (Binnenvlakken)

Reference (Referentie)

Mode (Modus):

Edit Mode (Bewerkingsmodus)

Menu:

Select ‣ Select All by Trait ‣ Interior Faces

Selects faces that may have been accidentally created inside the mesh instead of on the mesh’s surface. Specifically, it selects faces with “abnormal” neighbors (multiple neighbors connected to the same edge), as well as any “normal” neighbors of those faces.

Faces by Sides (Vlakken per Zijden)

Reference (Referentie)

Mode (Modus):

Edit Mode (Bewerkingsmodus)

Menu:

Select ‣ Select All by Trait ‣ Faces by Sides

Selects all faces that have a certain number of edges. The number can be specified in the Adjust Last Operation (Laatste operatie aanpassen) panel.

Poles by Count

Reference (Referentie)

Mode (Modus):

Edit Mode (Bewerkingsmodus)

Menu:

Select ‣ Select All by Trait ‣ Poles by Count

Finds vertices that are a pole, namely vertices that are connected to an irregular number of edges. Then, selects either those poles (in vertex selection mode) or the edges/faces connected to them (in edge/face selection mode).

Voordat polen worden geselecteerd.

Nadat polen zijn geselecteerd.

Options (Opties)

Pole Count (Aantal Polen)

Specifies the number of edges a vertex must (not) have to be considered a pole.

Type (Type)

Defines the comparison method for determining poles:

Less Than (Minder Dan):

Find vertices that have fewer edges than Pole Count.

Equal To (Gelijk Aan):

Find vertices that have exactly Pole Count edges.

Greater Than (Groter Dan):

Find vertices that have more edges than Pole Count.

Not Equal To:

Find vertices that have more or fewer edges than Pole Count.

Extend (Uitbreiden)

Adds to the existing selection rather than replacing it.

Exclude Non Manifold

Skips poles that are part of non-manifold geometry.

Hint

Poles can cause ugly pinching when using the Subdivision Surface Modifier, so this operator is useful for finding them.

Ungrouped Vertices (Ongegroepeerde Hoekpunten)

Reference (Referentie)

Mode (Modus):

Edit Mode (Bewerkingsmodus)

Menu:

Select ‣ Select All by Trait ‣ Ungrouped Vertices

Selects all vertices that are not part of any vertex group.