Pennello

Riferimento

Pannello:

Physics ‣ Dynamic Paint

Tipo:

Pennello

The Brush type makes object apply paint on the canvas.

Brush main panel.

From the first brush panel you can define how brush affects canvas color surfaces.

Paint Color

Color of the paint.

Trasparenza

Defines brush alpha or visibility. Final wetness is also affected by alpha.

Wetness

Defines how «wet» new paint is. Wetness is visible on «Paint» surface «wetmap». Speed of «Drip» and «Spread» effects also depends on how wet the paint is.

Absolute Alpha

This setting limits brush alpha influence. Without it, brush is «added» on surface over and over again each frame, increasing alpha and therefore influence of brush on canvas. In many cases however, it is preferred to not increase brush alpha if it already is on brushes level.

Erase Paint

Makes brush dissolve existing paint instead of adding it.

Sorgente

Riferimento

Tipo:

Pennello

Pannello:

Physics ‣ Dynamic Paint ‣ Source

Paint source setting lets you define how brush influence/intersection is defined.

Mesh Volume

The Brush affects all surface point inside the mesh volume.

Source: Mesh Volume.

Proximity

Only uses defined distance to the closest point on brush mesh surface. Note that inside of the volume is not necessarily affected because it is not close to the surface.

Source: Proximity. Brush affects all canvas pixels around it.

Mesh Volume + Proximity

Same as volume type, but also has influence over defined distance.

Inner Proximity

Applies proximity inside the mesh volume.

Negate Volume

Negates brush alpha within mesh volume.

The Volume + Proximity brush with no additional settings.	Inner Proximity. Proximity falloff is now visible inside the volume.
Negate Volume. Inner side of the volume has become completely transparent.	Inner Proximity and Negate Volume enabled together.

Object Center

Instead of calculating proximity to the brush object mesh, which can be quite slow in some cases, only distance to only center is calculated. This is much faster and often good enough.

Source: Object Center.

Particle System

Brush influence is defined by particles from a selected particle system.

Effect Solid Radius

Defines the distance, inside which paint is solid color.

Use Particle Radius

Uses the settings in the particle panel to determine solid radius size. Solid Radius size disabled while Particle Radius enabled.

Smooth Radius

An additional radius outside Solid Radius to add a smooth falloff.

If you set «Smooth Radius» to zero, particle will be painted as a solid sphere. If you set «Solid Radius» to zero, it gets painted as a smooth halo.

Source: Particle System.

Opzioni Comuni

Paint Distance

The maximum distance to mesh surface to affect paint.

Project

Projects brush to the canvas from a defined direction. Basically this can be considered as «direction aligned» proximity.

The Project option enabled. See how brush only affects canvas in normal direction.

Riduzione

Acuto:

Paints solid paint within the defined distance.

Smooth:

Makes paint to linearly fade out until becoming completely invisible when it reaches the maximum distance.

Rampa di colore:

Allows you to manually make a custom falloff behavior.

Velocity

Riferimento

Tipo:

Pennello

Pannello:

Physics ‣ Dynamic Paint ‣ Velocity

This panel shows brush options that are based on object velocity.

On top you have a color ramp and several related settings. Basically the color ramp represents brush velocity values: left side being zero velocity and right side being the «Max velocity». Speed is measured in «units per frame».

Checkboxes above can be used to define color ramp influence.

Multiply Alpha

Uses color ramp’s alpha value depending on current velocity and multiplies brush alpha with it.

Replace Color

Replaces the brush color with the values from the Widget Rampa Colore.

Multiply Depth

Multiplies brushes «depth intersection» effect. Basically you can adjust displace and wave strength depending on brush speed.

Do Smudge

Enabling Smudge makes the brush «smudge» (or «smear») existing colors on the surface as it moves. The strength of this effect can be defined from the Smudge Strength property.

Even when smudge is enabled brush still does its normal paint effect. If you want a purely smudging brush use zero alpha. It is also possible to have Erase option enabled together with smudge.

Waves

Riferimento

Tipo:

Pennello

Pannello:

Physics ‣ Dynamic Paint ‣ Waves

This panel is used to adjust brush influence to «Wave» surfaces.

Wave Type

Select what effect the brush creates in the wave simulation.

Depth Change:

The brush create waves when the intersection depth with the surface is changed on that point. If the brush is not moved, it will have no effect.

Using a negative «Factor» with this type can create a nice looking «wake» for moving objects like ships.

Obstacle:

Constantly affects surface whenever intersecting. Waves are also reflected off this brush type. However, due the nature of wave simulation algorithm this type creates an unnatural «dent» in the surface if the brush is not moved.

Force:

Directly affects the velocity of wave motion. Therefore the effect is not one-to-one with brush intersection depth, yet the force strength depends on it.

Reflect Only:

This type has no visible effect on the surface alone but reflects waves that are already on the surface.

Fattore

Adjusts how strongly brush «depth» affects the simulation. You can also use negative values to make brush pull water up instead of down.

Clamp Waves

In some cases the brush goes very deep inside the surface messing whole simulation up. You can use this setting to «limit» influence to only certain depth.