Esculpir¶
This page details the general hotkey operators and menu operators in sculpt mode.
Transform¶
- Mover
Change the position of the object.
- Rotate
Change the orientation of the mesh.
- Scale
Increase/decrease the size of the mesh.
- Esfera
Morph the mesh to a spherical shape.
Veja também
Show & Hide¶
Reference
- Mode:
Modo de escultura
- Menu:
Some very common hotkey operators to control the visibility based on face sets. These are not part of any menu and have to be used via the shortcuts. More visibility operators can be found in the Face Sets Menu and the Pie Menu shortcut W. (Since visibility is often toggled via face sets.)
- Box Hide
Draw a box to hide faces of a mesh.
- Box Show
Draw a box to reveal hidden faces. This works similar to the Box Select tool.
- Toggle Visibility Shift-H
Hide all face sets except the active one (under the cursor). If face sets are already hidden, then this operator will show everything.
- Hide Active Face Set H
Hide the face set under the cursor. Press Shift-H afterwards to show everything.
- Show All W, Alt-H
Reveal all hidden geometry.
- Invert Visible
Hides all visible geometry and makes all hidden geometry visible.
- Hide Masked
Hides all masked vertices.
- Grow/Shrink Visibility PageUp, PageDown
Grows or shrinks the visible area of the mesh along its surface.
Veja também
For a more general introduction see Visibility, Masking & Face Sets.
Fairing¶
These operators smooths geometry patches based of a Face set.
Veja também
- Fair Positions
Creates a perfectly flat and smooth geometry patch from the face set. This is the ideal way to trim parts of your mesh if the vertex count is too high for other operations, or the vertex IDs must not be altered (Like when using Multires sculpting).
- Fair Tangency
Creates a smooth as possible geometry patch from the face set by minimizing changes in vertex tangents. This is ideal for creating smooth curved surfaces on complex topology, where just using the smooth brush will not lead to desired results
Trimming¶
The trimming operators add or remove geometry from the mesh based on a gesture input. These operators are especially useful for sketching an early base mesh for further sculpting with the voxel remesher.
- Line Project
Flattens the geometry along a plane determined by the camera view and a drawn line. The region of the mesh being flattened is visualized by the side of the line that is shaded.
- Box Trim
Removes geometry based on a box selection.
- Lasso Trim
Removes geometry based on a lasso selection.
- Box Add
Adds geometry based on a box selection.
- Lasso Add
Adds geometry based on a lasso selection.
Mesh Filters¶
Applies a deformation to all vertices in the mesh at the same time. Masking, auto-masking and visibility will be taken into account.
To use these operators, click and drag away from left to right or from right to left for a negative effect.
Veja também
- Suavizar
Smooths the positions of the vertices to either polish surfaces or remove volume from larger shapes. Especially useful to fix most of the artifacts of the voxel remesher. This filter works similar to the Smooth brush.
- Surface Smooth
Eliminates irregularities of the mesh by making the positions of the vertices more uniform while preserving the volume of the object. This filter works similar to the Surface deformation type of the Smooth brush.
- Inflate
Displaces vertices uniformly along their normal. This filter works similar to the Inflate brush.
- Relax Topology
Tries to create an even distribution of quads without deforming the volume of the mesh. This filter works the same as holding Shift with the Slide Relax brush.
- Relax Face Sets
This will remove the jagged lines visible after drawing or creating a face set. This filter works the same as holding Shift with the Draw Face Set brush.
- Aguçar
Sharpens and smooths the mesh based on its curvature, resulting in pinching hard edges and polishing flat surfaces. Especially useful when sculpting hard surfaces and stylized models with creasing and flattening brushes.
- Enhance Details
Increases the high frequency surface details of the mesh by intensifying the difference between creases and valleys. This filter works similar to the inverted direction of the Smooth brush.
- Erase Multires Displacement
Deletes displacement information of the Multires Modifier, resetting the mesh to a regular subdivision surface result. This can be used to reset parts of the sculpt or to fix reprojection artifacts after applying a Shrinkwrap Modifier.
Negative strokes will intensify the displacement details, this method works similar to Enhance Details and can give better results in some circumstances.
- Aleatorizar
Randomly moves vertices along the vertex normal. This filter works similar to the Randomize Transform.
Sample Color¶
Reference
- Mode:
Modo de escultura
- Menu:
- Atalho:
Shift-X
Adjust the brush color of the Pintura tool to the color under the mouse cursor.
Set Pivot¶
Reference
- Mode:
Modo de escultura
- Menu:
Like Object and Edit Mode, Sculpt Mode also has a Pivot Point. This is because the basic move, rotate and scale transforms are also supported in Sculpt Mode. But the pivot point in Sculpt Mode is unique. It always moves together with the transformed mesh and can be both manually & automatically placed.
- Origem
Sets the pivot to the origin of the sculpt.
- Unmasked
Sets the pivot position to the average position of the unmasked vertices.
- Mask Border
Sets the pivot position to the center of the mask’s border. This operation will automatically happen when using Expand.
- Active Vertex
Sets the pivot position to the active vertex position.
- Surface Shift-RMB
Sets the pivot position to the surface under the cursor.
Dica
For more convenient placement of the pivot point it’s recommended to use the shortcut assigned to Surface.
Veja também
For a more general introduction see Transforming.
Rebuild BVH¶
Reference
- Mode:
Modo de escultura
- Menu:
Recalculates the BVH used by Dyntopo to improve performance, which might degrade over time while using Dyntopo.
Veja também
For a more general introduction see Adaptive Resolution.
Dynamic Topology Toggle¶
Toggles Dyntopo.
Transfer Sculpt Mode¶
Reference
- Mode:
Modo de escultura
- Menu:
- Atalho:
Alt-Q
Switches Sculpt Mode from the Active object to the object under the mouse. See Switching Objects for more information.
Veja também
For a more general introduction see Working with Multiple Objects.