Chọn cái Kết Nối (Select Linked)¶
Kết Nối (Linked)¶
Tham Chiếu [Reference]
- Chế Độ [Mode]:
Chế Độ Biên Soạn [Edit Mode]
- Trình Đơn [Menu]:
- Tổ Hợp Phím Tắt [Shortcut]:
Ctrl-L
Selects all the geometry that's connected directly or indirectly to the current selection. This is often useful when a mesh has disconnected but overlapping parts, where isolating them any other way would be tedious.
Instead of selecting an element and pressing Ctrl-L, it's also possible to simply hover the mouse over an element and press L. Alternatively, press Shift-L to deselect.
The Điều Chỉnh Thao Tác Trước Đây (Adjust Last Operation) panel has the following option:
- Phân Giới (Delimit)
Stop expanding the selection when it reaches certain boundaries. It's possible to activate multiple of these choices by clicking them with Shift-LMB.
- Normal (Pháp Tuyến/Bình Thường):
Stop at faces that have an opposite orientation.
- Nguyên Vật Liệu [Material]:
Stop at faces that have a different material.
- Đường Khâu (Seam):
Stop at edges that are marked as UV Seams.
- Sắc Cạnh/Đột Ngột (Sharp):
Stop at edges that are marked as Sharp.
- UVs:
Stop at island borders in any UV map.
Đường Ngắn Nhất (Shortest Path)¶
Tham Chiếu [Reference]
- Chế Độ [Mode]:
Chế Độ Biên Soạn [Edit Mode]
- Trình Đơn [Menu]:
- Tổ Hợp Phím Tắt [Shortcut]:
Ctrl-NCT (LMB)
Selects the geometry along the shortest path between the two most recently selected mesh elements.
To use the shortcut, first select the starting element normally, then select the destination element with Ctrl-LMB.
Shortest paths for vertices (left) and faces (right).¶
Các Tùy Chọn (Options)¶
- Edge Tag Edge Mode
What to do with the selected edges:
- Lựa Chọn (Select):
Simply select the edges.
- Nhãn Đường Khâu (Tag Seam):
Mark the edges as UV Seams.
- Nhãn Sắc Nhọn (Tag Sharp):
Mark the edges as Sharp.
- Nhãn Nếp Gấp (Tag Crease):
Give the edges a Crease value of 1.0.
- Nhãn Bo Tròn (Tag Bevel):
Give the edges a Bevel Weight of 1.0.
- Nhãn Dấu Cạnh Phong Cách Tự Do (Tag Freestyle Edge Mark):
Mark the edges as Freestyle edges.
- Bước theo Mặt (Face Stepping)
Allow diagonal paths for vertices and faces, and edge rings for edges.
- Khoảng Cách Cấu Trúc Liên Kết [Topology Distance]
Pick the path that crosses the least edges instead of the smallest distance.
- PHủ Kín Vùng (Fill Region) Shift-Ctrl-NCT (LMB)
Select all possible shortest paths instead of just one.
- Deselected, Selected, Offset
Options for selecting a "dashed line" of elements instead of a continuous one. The path will contain a repeating pattern of a few unselected items followed by a few selected ones. See also Hủy Chọn So Le (Checker Deselect).
Các Mặt Phẳng Bẹt Kết Nối (Linked Flat Faces)¶
Tham Chiếu [Reference]
- Chế Độ [Mode]:
Chế Độ Biên Soạn [Edit Mode]
- Trình Đơn [Menu]:
Grows the selection to include connected faces until a sharp corner is reached.
- Độ Sắc Nhọn (Sharpness)
The maximum allowed angle between two faces for them to be considered part of the same flat surface. This angle is measured between the face normals, meaning that coplanar faces have an angle of 0° (not 180°) and sharp corners have a greater angle than dull ones (not smaller).
To stop the selection at edges that were manually marked as Sharp, use Kết Nối (Linked) instead.