F-Curve Modifiers#
Ссылка
- Панель:
F-Curve modifiers are similar to object modifiers, in that they add non-destructive effects that can be adjusted at any time and layered to create more complex effects.
Modifiers are evaluated from top to bottom. You can change their order by dragging the dots in their top right corner.
Интерфейс (interface)#
- Имя (name)
By default, modifiers are named after their function, but this can be changed.
- Отключение
Click the checkbox in a modifier’s header to disable it.
- Удалить (delete)
Click the cross in a modifier’s header to delete it.
- Влияние (influence)
Lets you blend between the original curve and the modified one.
- Restrict Frame Range
- Начало/Конец (start/end)
The frame on which the modifier’s effect starts/ends.
- Blend In/Out
The number of frames, relative the start/end values above, it takes the modifier to fade in/out.
Adding a Modifier#
Панель модификатора.#
Modifiers can be managed on the Modifiers tab of the Sidebar. Select an F-Curve (in the channel region or by selecting one of its keyframes), then click the Add Modifier dropdown and choose the modifier to add.
Types of Modifiers#
Generator Modifier#
Creates a polynomial function. These are basic mathematical formulas that represent lines, parabolas, and other more complex curves, depending on the values used.
См.также
Также смотрите статью Gimbal на англоязычной Википедии и статью Карданов подвес на русскоязычной Википедии.
- Режим (mode)
Method used to represent the equation.
- Expanded Polynomial
Equation in the form \(y = A + Bx^1 + Cx^2 + ... + Dx^n\).
- Factorized Polynomial
Equation in the form \(y = (Ax + B)(Cx + D)\).
- Сложение (Additive)
Add the polynomial to the curve rather than replacing it.
- Порядок (Order)
The highest power of
xfor this polynomial.- Coefficient
The constants A, B, C… in the equation.
Built-in Function Modifier#
These are additional formulas, each with the same options to control their shape. Consult mathematics reference for more detailed information on each function:
- Тип (type)
Встроенная функция для использования:
Normalized Sine: \(sin(x)/x\)
- Сложение (Additive)
Add the function to the curve rather than replacing it.
- Амплитуда (amplitude)
Adjusts the Y scaling.
- Phase Multiplier
Adjusts the X scaling.
- Смещение фазы (phase offset)
Adjusts the X offset.
- Value Offset
Adjusts the Y offset.
Envelope Modifier#
Lets you reshape the curve. First, you define an envelope, which consists of two horizontal lines that more or less match the curve’s lower and upper bounds. Then, you add control points, where each point can push, squeeze, and stretch the envelope (and the curve along with it) at a certain frame.
The Envelope modifier.#
- Ссылка
The value which the envelope is centered around.
- Мин/Макс
The offset from the reference value to the envelope’s initial lower/upper bound.
- Add Control Point
Adds a control point at the current frame.
- Точка (point)
- Кадр (frame)
Кадр контрольной точки.
- Мин/Макс
The offset from the reference value to the envelope’s adjusted lower/upper bound at this frame.
Cycles Modifier#
Makes the curve repeat itself.
Примечание
The Cycles Modifier can only be the first modifier.
- Before/After Mode
- No Cycles
Do not repeat the curve before/after the original.
- Repeat Motion
Repeats the curve, keeping the values of each copy the same.
- Repeat with Offset
Repeats the curve, offsetting each copy vertically so that its first keyframe matches the previous last keyframe.
- Repeat Mirrored
Repeats the curve, flipping every other copy horizontally.
- Количество (count)
Количество создаваемых копий. Значение 0 означает бесконечность.
Trivially Cyclic Curves#
When the Cycle Mode for both ends is set to either Repeat Motion or Repeat with Offset, and no other options of the modifier are changed from their defaults, it defines a simple infinite cycle.
This special case receives some additional support from other areas of Blender:
Automatic Bézier handle placement is aware of the cycle and adjusts to achieve a smooth transition.
The Cycle-Aware Keying option can be enabled to take the cycle into account when inserting new keyframes.
Noise Modifier#
Modifies the curve with a noise formula. This is useful for adding subtle or extreme randomness to animated movements, like camera shake.
- Blend Type
- Заменить (replace):
Adds noise in the range [-0.5, 0.5].
- Добавить (add):
Добавляет шум в диапазоне [0, 1].
- Вычесть (subtract):
Subtracts noise in the range [0, 1].
- Перемножить (multiply):
Multiplies by noise in the range [0, 1].
- Масштаб (scale)
Changes the horizontal scale of the noise. Higher values make for less dense oscillation.
- Сила (strength)
Изменяет вертикальный масштаб шума.
- Смещение (offset)
Offsets the noise in time.
- Фаза (phase)
Adjusts the random seed of the noise.
- Глубина (depth)
Adjusts how detailed the noise function is.
Limits Modifier#
Limits the curve to specific time and value ranges.
- Minimum, Maximum X
Removes the original curve data to the left of the minimum frame and to the right of the maximum, replacing it by Constant extrapolation.
- Minimum, Maximum Y
Clamps the curve values, never letting them go below the minimum or above the maximum.
Stepped Interpolation Modifier#
Gives the curve a stepped appearance by sampling it every N frames and making it hold its value after each sample. In a sense, this lowers the curve’s frame rate by letting it change its value less frequently, producing choppy movement as a result.
- Размер шага (step size)
Количество кадров для хранения каждого шага.
- Смещение (offset)
Количество кадров для смещения точек сэмплинга.
- Начальный кадр (start frame)
Кадр, с которого начнётся применение эффекта.
- End Frame
Кадр, на котором следует прекратить применение эффекта.