Đường Đi của Ánh Sáng (Light Paths)¶
Tham Chiếu (Reference)
- Panel (Bảng):
Thể Loại Tia Xạ (Ray Types)¶
Ray types can be divided into four categories:
Camera: the ray comes straight from the camera.
Reflection: the ray is generated by a reflection off a surface.
Transmission: the ray is generated by a transmission through a surface.
Shadow: the ray is used for (transparent) shadows.
Reflection and transmission rays can further have these properties:
Diffuse: the ray is generated by a diffuse reflection or transmission (translucency).
Glossy: the ray is generated by a glossy specular reflection or transmission.
Singular: the ray is generated by a perfectly sharp reflection or transmission.
The Light Path node can be used to find out the type of ray the shading is being computed for.
Xem thêm
The object tầm nhìn của tia xạ (ray visibility) settings.
Điều Khiển Bật Nẩy (Bounce Control)¶
The maximum number of light bounces can be controlled manually. While ideally this should be infinite, in practice a smaller number of bounces may be sufficient, or some light interactions may be intentionally left out for faster convergence. The number of diffuse reflection, glossy reflection and transmission bounces can also be controlled individually.
Light paths are terminated probabilistically when specifying a minimum number of light bounces lower than the maximum. In that case, paths longer than minimum will be randomly stopped when they are expected to contribute less light to the image. This will still converge to the same image, but renders faster while possibly being noisier.
Độ Trong (Transparency)¶
The BSDF Trong Suốt (Transparent BSDF) shader is given special treatment. Rays pass straight through it, changing neither direction nor type as if there were no geometry at all.
Alpha pass output is also different for the transparent BSDF. Other transmission BSDFs are considered opaque, because they change the light direction. As such they cannot be used for alpha-over compositing, while this is possible with the transparent BSDF.
Note that, while semantically the ray passes through as if no geometry was hit, rendering performance is affected as each transparency step requires executing the shader and tracing a ray.
Các Sắp Đặt (Settings)¶
Số Lần Bật Nẩy Tối Đa (Max Bounces)¶
- Tổng Số (Total)
Maximum number of light bounces. For best quality, this should be set to the maximum. However, in practice, it may be good to set it to lower values for faster rendering. A value of 0 bounces results in direct lighting only.
- Khuếch Tán (Diffuse)
Số lần lặp lại tối đa quá trình giải nghiệm.
- Bóng Bẩy (Glossy)
Số lần lặp lại tối đa quá trình giải nghiệm.
- Truyền Xạ (Transmission)
Số lần lặp lại tối đa quá trình giải nghiệm.
- Âm Lượng/Thể Tích (Volume)
Số lần lặp lại tối đa quá trình giải nghiệm.
- Trong Suốt (Transparent)
Số lần lặp lại tối đa quá trình giải nghiệm.
Note, the maximum number of transparent bounces is controlled separately from other bounces. It is also possible to use probabilistic termination of transparent bounces, which might help rendering many layers of transparency.
Clamping (Hạn Định)¶
- Ánh Sáng Trực Tiếp (Direct Light)
Tùy chọn này giới hạn cường độ tối đa mà một mẫu từ các tia chưa dội lại có thể đóng góp vào một điểm ảnh. Tùy chọn này tuy giảm nhiễu song sẽ không chính xác nữa. Đặt tùy chọn này thành 0.0 sẽ hoàn toàn tắt tính năng hạn định. Giá trị thấp hơn có ảnh hưởng lớn hơn (mẫu lấy tối hơn) trên hình ảnh kết quả hơn là các giá trị cao.
Ghi chú
This option provides a way to limit Fireflies. However, note that as you clamp out such values, other bright lights/reflections will be dimmed as well.
Care must be taken when using this setting to find a balance between mitigating fireflies and losing intentionally bright parts. It is often useful to clamp indirect bounces separately, as they tend to cause more fireflies than direct bounces. See the Clamp Indirect setting.
- Ánh Sáng Gián Tiếp (Indirect Light)
The same as Direct Light, but for rays which have bounced multiple times.
Caustics (Tụ Quang)¶
A common source of noise is Caustics.
Xem thêm
See Reducing Noise for examples of the clamp settings in use.
- Thanh Lọc Ánh Bóng Bẩy (Filter Glossy)
When using a value higher than 0.0, this will blur glossy reflections after blurry bounces, to reduce noise at the cost of accuracy. 1.0 is a good starting value to tweak.
Some light paths have a low probability of being found while contributing much light to the pixel. As a result these light paths will be found in some pixels and not in others, causing Fireflies. An example of such a difficult path might be a small light that is causing a small specular highlight on a sharp glossy material, which is observed through a rough glossy material. In fact in such a case there practically occurs a caustic.
With path tracing it is difficult to find the specular highlight, but if you increase the roughness on the material, the highlight gets bigger and softer, and so easier to find. Often this blurring will hardly be noticeable, because it is blurred by the material anyway, but there are also cases where this will lead to a loss of detail in lighting.
- Caustics (Tụ Quang)
- Có Tính Phản Xạ (Reflective)
While in principle path tracing supports rendering of caustics with a sufficient number of samples, in practice it may be inefficient to the point that there is just too much noise. This option can be unchecked, to disable reflective caustics.
- Có Tính Khúc Xạ (Refractive)
The same as above, but for refractive caustics.
Ước Tính GI Nhanh (Fast GI Approximation)¶
Tham Chiếu (Reference)
- Panel (Bảng):
Approximate diffuse indirect light with background tinted ambient occlusion. This provides fast alternative to full global illumination (GI), for interactive viewport rendering or final renders with reduced quality.
- Phương Pháp (Method)
Phương pháp ước tính GI nhanh.
- Thay Thế (Replace):
Thay thế ánh sáng toàn cầu bằng tính hấp thụ quang xạ môi trường sau một số lần bật nảy chỉ định nào đó.
- Thêm (Add):
Thêm tính hấp thụ quang xạ môi trường (THTMT) vào các bề mặt khuếch tán.
- Hệ Số THTMT (AO Factor)
The strength of the ambient occlusion.
- Khoảng Cách AO (AO Distance)
Distance from shading point to trace rays. A shorter distance emphasizes nearby features, while longer distances make it also take objects farther away into account.
This option can also be overridden per object in the Object Properties, which is useful when you have both small and large scale objects in the same scene.
- Lượng Bật Nẩy Cổng Nhìn (Viewport Bounces)
Replace global illumination with ambient occlusion after the specified number of bounces when rendering in the 3D Viewport. This can reduce noise in interior scenes with little visual difference.
- Kết Xuất các Bật Nảy (Render Bounces)
Number of bounces when rendering final renders.