Select Linked – Вибір Пов’язане

Linked – Пов’язане

Посилання

Режим:

Edit Mode – Режим Редагування

Меню:

Select ‣ Select Linked ‣ Linked

Скорочення:

Ctrl-L

Selects all the geometry that’s connected directly or indirectly to the current selection. This is often useful when a mesh has disconnected but overlapping parts, where isolating them any other way would be tedious.

Instead of selecting an element and pressing Ctrl-L, it’s also possible to simply hover the mouse over an element and press L. Alternatively, press Shift-L to deselect.

The Наладнати Останню Операцію – Adjust Last Operation panel has the following option:

Розмежування – Delimit

Stop expanding the selection when it reaches certain boundaries. It’s possible to activate multiple of these choices by clicking them with Shift-LMB.

Нормальний:

Stop at faces that have an opposite orientation.

Матеріал:

Stop at faces that have a different material.

Шов – Seam:

Stop at edges that are marked as UV Seams.

Sharp – Гостро:

Stop at edges that are marked as Sharp.

UVs:

Stop at island borders in any UV map.

Найкоротший Шлях – Shortest Path

Посилання

Режим:

Edit Mode – Режим Редагування

Меню:

«Вибір > Вибрати Пов’язане > Найкоротший Шлях» – Select ‣ Select Linked ‣ Shortest Path

Скорочення:

Ctrl-LMB

Selects the geometry along the shortest path between the two most recently selected mesh elements.

To use the shortcut, first select the starting element normally, then select the destination element with Ctrl-LMB.

Shortest paths for vertices (left) and faces (right).

Options – Опції

Edge Tag Edge Mode

What to do with the selected edges:

Обрати:

Simply select the edges.

Значити Шов – Tag Seam:

Mark the edges as UV Seams.

Значити Гостре – Tag Sharp:

Mark the edges as Sharp.

Значити Складку – Tag Crease:

Give the edges a Crease value of 1.0.

Значити Скіс – Tag Bevel:

Give the edges a Bevel Weight of 1.0.

Значити Позначку Ребра Freestyle – Tag Freestyle Edge Mark:

Mark the edges as Freestyle edges.

Крокування Гранями – Face Stepping

Allow diagonal paths for vertices and faces, and edge rings for edges.

Topology Distance

Pick the path that crosses the least edges instead of the smallest distance.

Заповнити Регіон – Fill Region Shift-Ctrl-LMB

Select all possible shortest paths instead of just one.

Deselected, Selected, Offset

Options for selecting a «dashed line» of elements instead of a continuous one. The path will contain a repeating pattern of a few unselected items followed by a few selected ones. See also Зневибрати Шахово – Checker Deselect.

Пов’язані Плоскі Грані – Linked Flat Faces

Посилання

Режим:

Edit Mode – Режим Редагування

Меню:

Select ‣ Select Linked ‣ Linked Flat Faces

Grows the selection to include connected faces until a sharp corner is reached.

Гострота – Sharpness

The maximum allowed angle between two faces for them to be considered part of the same flat surface. This angle is measured between the face normals, meaning that coplanar faces have an angle of 0° (not 180°) and sharp corners have a greater angle than dull ones (not smaller).

Initial selection.

After running Select Linked Flat Faces.

Comparison to Select Similar ‣ Normal.

To stop the selection at edges that were manually marked as Sharp, use Linked – Пов’язане instead.